Manuals / Enviro / Household Appliance / Stove

Enviro EF-119 owner manual Installation, Dimensions of EF2 Freestanding, Dimensions - Freestanding

Models: EF-119

1 39

Download 39 pages 20.59 Kb

Page 12

Image 12

Installation

DIMENSIONS - FREESTANDING:

��

Figure 6: Dimensions of EF2 Freestanding.

DIMENSIONS - FIREPLACE INSERT AND BUILT-IN HEATER:

��

Figure 7: Dimensions of EF2 Fireplace Insert and Built-In Heater.

Page 12

Image 12

Enviro EF-119 Installation, Dimensions of EF2 Freestanding, Dimensions of EF2 Fireplace Insert and Built-In Heater

Contents

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TOFOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATHTable of Contents Introduction Pellet quality is important, please read the followingP.F.I. PELLET STANDARDS Store pellets at least 36” 1 m away from the pellet stoveIMPORTANT SAFETY DATA SAFETY WARNINGS AND RECOMMENDATIONSIntroduction Caution Do not connect to any air distribution duct or systemIntroduction SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCEKEEP ASH PAN FREE OF RAW FUEL Operating Instructions THE REASONS WHY THE UNIT OVERHEATEDSPECIAL NOTES Operating Instructions 1. Check and fill hopper with pelletsRoutine Cleaning and Maintenance TOOLS REQUIRED TO CLEAN UNITBURN POT AND LINER 2-3 days INSIDE FIREBOX 2-3 daysRoutine Cleaning and Maintenance Removal of the firebox backing for bi-annual cleaningNOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN FREESTANDING ASH PANRoutine Cleaning and Maintenance Installation of firebox backingPOST SEASON CLEAN-UP CLEANING PLATED SURFACESInstallation Installation Figure 6 Dimensions of EF2 FreestandingFigure 7 Dimensions of EF2 Fireplace Insert and Built-In Heater DIMENSIONS - FREESTANDINGInstallation 6 inches15.2 cm Figure 9 EF2 Freestanding Minimum Alcove SizeInstallation or from the outside of the pedestal for the FPI or BIHInstallation NOTE Venting terminals shall not be recessed into walls or sidingInstallation EXHAUSTFreestanding Fireplace InsertInstallation Secure the heater to the floor using the 2 two holes in the pedestalInstallation stoveWall thimbleInstallation Figure 23 is the recommended installation set upInstallation 2. Place a non-combustible hearth pad where necessaryInstallation connector at the fireplaceFigure 26 Outside Vertical Installation Figure 27 Freestanding hearth mount installationInstallation Figure 28 Freestanding hearth mount installation overviewMASONRY FIREPLACE INSTALLATION - FIREPLACE INSERT Installation 6. Recommended Install freshFigure 29 Masonry fireplace installation fromInstallation This unit includes a 3” 75 mm pedestalInstallation 3. Plug the wiring harness into the control panel see FigureInstallation Figure 37 Slider / damper assemblyREMOVAL Figure 36 Side surround panel swings forwardTroubleshooting DO NOTWHAT TO DO IF 1. The stove will not startTroubleshooting 3. The stove will not function in the “AUTO” mode when hotw If the motor runs, have your dealer check the harness 4. The exhaust motor will not function normallyTroubleshooting 7. The auger motor will not function normallyTroubleshooting 8. The dial-a-fire has no effect on the firePotentiometer Readings 9. The stove will not shut offWiring Diagram Parts List Parts List EF-113EF-115 EF-117Parts List Parts List - Options ComponentsDPartsiagram FebruaryDiagram - Steel PartsFebruary Warranty WHEN FILING A WARRANTY CLAIM PLEASE COMPLETE THE FOLLOWINGINFORMATION ON AN OFFICIAL WARRANTY CLAIM FORM For the do-it-yourself IndividualInstallation Data Sheet 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3