Manuals / Enviro / Household Appliance / Stove

Enviro EF-119 owner manual Installation, Freestanding hearth mount installation overview

Models: EF-119

1 39

Download 39 pages 20.59 Kb

Page 22

Image 22

Installation

��

Figure 28: Freestanding hearth mount installation overview.

MASONRY FIREPLACE INSTALLATION - FIREPLACE INSERT:

The fireplace insert model requires a surround panel and a pedestal. When installing this unit, ensure that the pedestal is removed from the inside of the hopper and installed on the bottom of the unit (see

“PEDESTAL INSTALLATION”).

Assemble surround panel (see “INSTALLATION OF CONTROL PANEL INTO SURROUND PANEL - FPI AND BIH” and “INSTALLATION AND REMOVAL OF THE SURROUND PANELS - FPI AND BIH”) before starting installation.

A non-combustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater.

1.Install the hearth pad.

2.Lock the fireplace damper in the open position.

3.Install a positive flue connector at the fireplace damper.

Page 22

Image 22

Enviro EF-119 owner manual Installation, Freestanding hearth mount installation overview

Contents

FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATIONAND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO DAMAGE, BODILY INJURY, OR EVEN DEATHTable of Contents P.F.I. PELLET STANDARDS IntroductionPellet quality is important, please read the following Store pellets at least 36” 1 m away from the pellet stoveIntroduction IMPORTANT SAFETY DATASAFETY WARNINGS AND RECOMMENDATIONS Caution Do not connect to any air distribution duct or systemSAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE IntroductionKEEP ASH PAN FREE OF RAW FUEL THE REASONS WHY THE UNIT OVERHEATED Operating InstructionsSPECIAL NOTES Operating Instructions 1. Check and fill hopper with pelletsBURN POT AND LINER 2-3 days Routine Cleaning and MaintenanceTOOLS REQUIRED TO CLEAN UNIT INSIDE FIREBOX 2-3 daysNOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN Routine Cleaning and MaintenanceRemoval of the firebox backing for bi-annual cleaning FREESTANDING ASH PANPOST SEASON CLEAN-UP Routine Cleaning and MaintenanceInstallation of firebox backing CLEANING PLATED SURFACESInstallation Figure 7 Dimensions of EF2 Fireplace Insert and Built-In Heater InstallationFigure 6 Dimensions of EF2 Freestanding DIMENSIONS - FREESTANDING15.2 cm Installation6 inches Figure 9 EF2 Freestanding Minimum Alcove SizeInstallation or from the outside of the pedestal for the FPI or BIHInstallation NOTE Venting terminals shall not be recessed into walls or sidingFreestanding InstallationEXHAUST Fireplace InsertInstallation Secure the heater to the floor using the 2 two holes in the pedestalWall Installationstove thimbleInstallation Figure 23 is the recommended installation set upInstallation 2. Place a non-combustible hearth pad where necessaryFigure 26 Outside Vertical Installation Installationconnector at the fireplace Figure 27 Freestanding hearth mount installationFigure 28 Freestanding hearth mount installation overview InstallationMASONRY FIREPLACE INSTALLATION - FIREPLACE INSERT Figure 29 Masonry fireplace installation Installation6. Recommended Install fresh fromInstallation This unit includes a 3” 75 mm pedestalInstallation 3. Plug the wiring harness into the control panel see FigureREMOVAL InstallationFigure 37 Slider / damper assembly Figure 36 Side surround panel swings forwardWHAT TO DO IF TroubleshootingDO NOT 1. The stove will not startw If the motor runs, have your dealer check the harness Troubleshooting3. The stove will not function in the “AUTO” mode when hot 4. The exhaust motor will not function normallyTroubleshooting 7. The auger motor will not function normallyPotentiometer Readings Troubleshooting8. The dial-a-fire has no effect on the fire 9. The stove will not shut offWiring Diagram Parts List EF-115 Parts ListEF-113 EF-117Parts List Parts List - Options ComponentsDPartsiagram FebruaryParts Diagram - SteelFebruary INFORMATION ON AN OFFICIAL WARRANTY CLAIM FORM WarrantyWHEN FILING A WARRANTY CLAIM PLEASE COMPLETE THE FOLLOWING For the do-it-yourself IndividualInstallation Data Sheet 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3