Epson I+ Replacing the Cover

Replacing the Cover

With the option card properly installed or removed, the last step is to replace the cover of the main unit:

1.With the back of the main unit facing you, position the cover over the computer with the side feet to the left of the main unit and the front edge pointing slightly downward.

2.Lower the cover onto the bottom half of the case, as shown in Figure 3-6, making sure that the bottom edges fit inside the case. At the same time, slide the front edge beneath the top edge of the front panel. Finally, lower the back of the cover so that it is in position.

Figure 3-6. Replacing the cover

3.Secure the cover by replacing the screws on both sides of the main unit. Snap the plastic inserts into the side feet.

4.Replace the back panel and the three screws along the top edge.

5.Return the computer to its original position and reconnect it to the monitor, the keyboard, and any other peripherals you have.

6.Check to make sure the power switch is off. Reconnect the power cable to the back of the main unit and to an electrical outlet. Change the DIP switches if necessary.

3-6

Contents

Page Page IMPORTANT NOTICE DISCLAIMER OF WARRANTY COPYRIGHT NOTICE TRADEMARKS Epson is a registered trademark of Seiko Epson Corporation Note: WARNING Contents Appendixes Tables Introduction How to Use This Manual Setting Up Your System 1 Unpacking Removing the disk drive protector sheet 2 Choosing a Location 3 Arranging the Components The Figure 1-2.Rear panel The front panel Figure 1-3.Front panel 4 Connecting the Power Cord Figure 1-4.herring the power cord 5 Connecting the Video Monitor 6 Connecting the Keyboard Figure the unit 7 Connecting the Printer Parallel interface PARALLEL Serial interface The Equity I+ character set 8 Setting the DIP Switches DIP switch set 1 (internal operations) Enhanced Page DIP switch set 2 (parallel and serial port operations) Page 9Turning On the Computer Safety rules Initial setup procedure Initial screen display Page Using Your Equity I+ Special Keys Selecting Execution Speed Resetting the Computer Turning Off the Computer Using Disks and Disk Drives How disks work Choosing diskettes for the Equity I+ Caring for your disks and disk drives Page Inserting and removing diskettes blank Write-protectingdiskettes Making backup copies Using a single floppy disk drive Using a hard disk drive Page Installing Option Cards Removing the Cover Page Figure 3-3.Removing cover Inserting the Option Card Inserting Removing an access slot cover Replacing the Cover Post-installationSetup Removing Option Cards Troubleshooting The Computer Fails to Start Up The Video Display Does Not Appear The Computer Locks Up or Freezes Floppy Disk Problems Hard Disk Problems Software Problems Printer Problems Option Card Problems Changing Jumper Settings Figure A-1.Jumper positions Jumper J1, Floppy Disk Controller Figure A-2.Jumper locutions Jumper J2, Parity RAM Specifications Main Unit Keyboard Mass Storage Power Supply Environmental Requirements Physical Characteristics (CPU Only) Video and Display Options Glossary Command Configuration Control code Cursor Data Disk drive Diskette Double-density File Floppy disk H a r d w a r e Input/output port Interface Jumper Kilobyte (KB) Monochrome monitor MS-DOS Operating system Option card Parallel Read Read/write head Reset RGB ROM Tracks Write To store data on a disk Write-protect C-7 Index Index-2 Page Index-4 Page Page IMPORTANT NOTICE Contents Moving the Hard Disk System-dependentUtilities Appendixes Tables Introduction Page Running the Diagnostics Starting the Diagnostics The Power-onSelf Test The OPERATION MENU Exiting Diagnostics Diagnostics and MS-DOSCommands Page Setting Up the System Using the Setup Program ESC ** SAVE SETTINGS Change settings Exit without saving ** EXIT AND SAVE Setting the Real-timeClock block Real-time Changing Serial Port (RS-232C)Settings Baud Stop 300bps Data length Formatting a Hard Disk Formatting and Checking Options Enter drive letter (C/D) Conditional Format (Normal) Scanning Format cancelled Press ENTER to return to the menu Now formatting Format finished Flagging bad tracks Unconditional Format Destructive Surface Analysis Page Non-destructiveSurface Analysis Formatting a Diskette Insert new diskette for drive A: and strike ENTER when ready Performing System Diagnostics Using the System Diagnostics Program 2 - Memory 3 - Keyboard 11- Serial port (RS-232Cport) 14- Dot-matrixprinter by Enter. You see a Modify DEVICE LIST l - Add devices 2 - Delete devices 0 and Enter and Page System Board Check Memory Check Keyboard Check Monochrome Display Adapter and CRT Check Attribute Character Video check Is the display correct (Y/N) Character set check by Enter Color Graphics Adapter and CRT Check 1 and Page Y and Enter Enter to 640x200 graphics mode check To check your 640x200 graphics mode, press 6 and Enter 640X200 GRAPHICS MODE CHECK MODE Is the display correct (Y/N) 8 and Enter. To Floppy Disk Drives and Controller Check Sequential seek check Current track is Random seek check Write, read check If using drive A, remove your Diagnostics Disk Math Coprocessor Check (8087) Parallel Port (Printer Interface) Check Enter Y to start this check when connector is Parallel Port (on Video Adapter) Check Serial Port (RS-232C)Check Alternate Serial Port Check Dot-matrixPrinter Check Hard Disk Drives and Controller Check When you select option 17 from the DEVICE LIST, you see this menu: HARD DISK DRIVE(S) AND CONTROLLER CHECK MENU l- Seek check 2- Write, read check 3- Error detection. and correction check 4- Read, verify check 5- Run all above checks Page READ TRACKS Moving the Hard Disk System-dependentUtilities The HELP Utility When the menu is displayed, you see this prompt at the bottom of the screen: Select command name, Enter to display command, Esc to Exit Page Up Pg Up) Esc HELP Caution The ROMBIOS Utility The SYSTAT Utility Type SYSTAT only and press Enter. You see a screen similar to this: CPU speed Display type Coprocessor Real-timeclock Esc Error Codes and Messages Table A-1. Error codes and messages Table A-1.Error codes and messages (continued) x 200 GRAPHICS MODE 703COPROCESSOR INVALID OPERATION MASK ERROR COPROCESSORSUBTRACTION ERROR Table A-1Error codes and messages (continued) ERROR DTR DSR, DSR ALWAYS HIGH/LOW ERROR RTS CTS, CTS ALWAYS HIGH/LOW status error- t y p e Power-onDiagnostics System Device Check Clock and CMOS RAM Check 161-Systemoptions not set (Run SETUP in DIAGNOSTICS) RAM Check Keyboard Controller and Keyboard Check Floppy Disk Drive Seek Check Index