Epson LX-300 FCC Compliance Statement

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio or

television reception. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause interference to radio and television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures.

❏Reorient or reloca te the rece iving antenna

❏Increase the separation between the equipment and receiver

❏Connect the equipment into an outlet on a circuit different from that to which the

receiver is conne cted

❏Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will

invalidate the FC C Certificatio n of this dev ice and may cau se interfere nce levels w hich

exceed the limits established by the FCC for this equipment. It is the responsibility of the

user to obtain and use a shielded equipment interface cable with this device. If this

equipment has more than one interface connector, do not leave cables connected to unused

interfaces.

Changes or modifications not expressly approved by the manufacturer could void the

user’s authority to operate the equipment.

For Canadian Users

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus as set out in the radio interference regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de Classe B prescrites dans le règlement sur le

brouillage radioélectrique édicté par le Ministère des Communications du Canada.

L

Blueberry REV.E

A5 size Front

95/04/17

ii

Contents

Main Page EPSON LX-300 Users Guide FCC Compliance Statement For United States Users ii For Canadian Users A5 size Front 95/04/17 Where to Get Help for United States Users For United Kingdom Users Epson product guarantee iv Use of options Safety information vi Contents Introduction Chapter 1 Setting Up the Printer Chapter 2 Using the Printer Chapter 3 Troubleshooting viii Appendix Index x Introduction Features Finding Your Way Around Warnings, Cautions, and Notes 2 w c Notes Important Safety Instructions 4 Chapter 1 Setting Up the Printer Unpacking the Printer 1-2 Choosing a place for the printer Assembling the Printer Installing the paper-feed knob 1-4 Attaching the paper supports Installing the ribbon cartridge w 1-6 Page 1-8 Plugging in the printer Running the Self Test 1-10 PAUSE 1-12 Connecting the Printer to Your Computer Using the parallel interface 1-14 Using the serial interface Setting Up Your Software 1-16 Microsoft Windows Using non-Windows software 1-18 Chapter 2 Using the Printer Using the Control Panel Lights and buttons 2-2 FONT 1 and FONT 2 lights FONT button Page Selecting fonts 2-4 Printing on Single Sheets Loading single sheets Adjusting the loading position Getting the results you expect 2-6 Printing on Continuous Paper Printing with the push tractor 2-8 Page 2-10 Switching back to single sheets Printing with the pull tractor 2-12 Page 2-14 Printing on Special Paper Adjusting the paper-thickness lever 2-16 Multi-part forms Labels Envelopes 2-18 Changing the Printer Settings 2-20 Page Printer setting descriptions Character spacing 2-22 Shape of zero Skip-over-perforat ion Character table Auto line feed Page length Auto tear off Tractor Installing and Using Options Cut-sheet feeder Page 2-26 Page Pull Tractor unit 2-28 Roll paper holder 2-30 Color upgrade kit 2-32 Page 2-34 Chapter 3 Troubleshooting Problems and Solutions FONT 3-2 LF/FF Power Supply Printing The printer does not print The print is faint or uneven Dots are missing in printed characters or graphics 3-4 Printed characters are not what you expected The print position is not what you expected Paper Handling Single sheets do not feed properly 3-6 Continuous paper does not feed properly Options When you use the cut-sheet feeder, the paper does not feed properly 3-8 Switching between the cut-sheet feeder and the push tractor does not work properly Using the pull tractor with the push tractor, continuous paper does not feed properly With color upgrade kit installed, printer doesnt operate properly 3-10 Appendix Printer Specifications Printing A-2 Paper Appendix A-3 A-4 Appendix A-5 Mechanical Electrical A-6 Environmental Safety approvals Interface Specifications Parallel interface specifications Serial interface specifications Serial pin assignments A-8 Printer Settings Appendix A-9 A5 size Appendix 95/04/17 Command Summary Sending printer commands A-10 Using the command summary Printer operation Data control Appendix A-11 Vertical motion Horizontal motion A-12 Overall printing style Print size and character width Appendix A-13 Print enhancement Word processing Character tables A-14 User-defined characters Appendix A-15 Color printing Graphics A-16 Index A Index 1 B C M N 2 O P T U Index 3 W Z