Epson RX-8801SA/JE NOTICE

NOTICE

•The material is subject to change without notice.

•Any part of this material may not be reproduced or duplicated in any form or any means without the written permission of Epson Toyocom.

•The information, applied circuit, program, usage etc., written in this material is just for reference. Epson Toyocom does not assume any liability for the occurrence of infringing any patent or copyright of a third party. This material does not authorize the licensing for any patent or intellectual copyrights.

•Any product described in this material may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export licence from the Ministry of International Trade and industry or other approval from another government agency.

•You are requested not to use the products (and any technical information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you would not make the products available to any third party who may use the products for such prohibited purposes.

•These products are intended for general use in electronic equipment. When using them in specific applications that require extremely high reliability such as applications stated below, it is required to obtain the permission from Epson Toyocom in advance.

/Space equipment (artificial satellites, rockets, etc) / Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc) / Medical instruments to sustain life / Submarine transmitters

/Power stations and related / Fire work equipment and security equipment / traffic control equipment

/and others requiring equivalent reliability.

•In this manual for Epson Tyocom, product code and marking will still remain as previously

identified prior to the merger.Due to the on going strategy of gradual unification of part numbers, please review product code and marking as they will change during the course of the coming months.

We apologize for the inconvenience, but we will eventually have a unified part numbering system for Epson Toyocom which will be user friendly.

Contents

Page NOTICE RX - 8801 SA / JE Contents 2. Block Diagram 3. Terminal description 4. Absolute Maximum Ratings I2C-BusInterface Real-timeClock Module 1. Overview 2. Block Diagram 3. Terminal description RX − 8801 SA RX − 8801 JE 4. Absolute Maximum Ratings Item Symbol Condition Rating 7. Electrical Characteristics •Temperature compensation and consumption current Protocol SCL SDA 8. Use Methods 8.2. Description of Registers 8.2.1. Register table Address Remark SEC MIN 8.2.2. Control register (Reg F) Control Register CSEL1 1) CSEL0,1 ( Compensation interval Select 0, 1 ) bits CSEL0,1 3) AIE ( Alarm Interrupt Enable ) bit When an alarm interrupt event occurs, an interrupt signal is not generated or is canceled (/INT status changes from low to Hi-Z) When an alarm interrupt event occurs, an interrupt signal is generated (/INT status changes from Hi-Zto low) Flag register 1)UF ( Update Flag ) bit 2)TF ( Timer Flag ) bit 3)AF ( Alarm Flag ) bit 4)VLF ( Voltage Low Flag ) bit Extension Register USEL TSEL1 1)TEST bit This is the manufacturer's test bit. Its value should always be "0 8.2.6. Clock counter (Reg - 0 ∼ 2) •The clock counter counts seconds, minutes, and hours The data format is BCD format 1) Second counter 00 seconds Month Date update pattern 1, 3, 5, 7, 8, 10, or 4, 6, 9, or February in normal year 8.3. Fixed-cycleTimer Interrupt Function 8.3.1. Diagram of fixed-cycletimer interrupt function TE bit TIE bit /INT output TSEL1 TSEL0 Flag Register When the 1) TSEL0,1 bits (Timer Select 0, 1) SCL pin SDA pin /INT pin 8.4. Time Update Interrupt Function ∗When the RESET bit value is "1" time update interrupt events do not occur 1) USEL (Update Interrupt Select) bit Selects "second update" (once per second) as the timing for generation of interrupt events Selects "minute update" (once per minute) as the timing for generation of 8.5. Alarm Interrupt Function ∗When the RESET bit value is "1" alarm interrupt events do not occur 1) WADA (Week Alarm /Day Alarm) bit WADA Sets WEEK as target of alarm function (DAY setting is ignored) 3) AF (Alarm Flag) bit The AF bit is cleared to zero to prepare for the next status detection Alarm interrupt events are not detected Alarm interrupt events are detected 4) AIE (Alarm Interrupt Enable) bit 8.6. Reading/Writing Data via the I2C Bus Interface 0.95 s ( Max. ) 1) START condition, repeated START condition, and STOP condition (1)START condition The SDA level changes from high to low while SCL is at high level (2)STOP condition However, the transfer time must be no longer than 0.95 seconds After address Fh, incrementation goes to address 0h [0110 65 h 64 h Page Unit I2C-BUS Master RX-8801 9. External Dimensions / Marking Layout 9.1. RX − 8801 SA ( SOP − 14pin ) ( SOP 14pin ) 9.1.1. External dimensions 9.2.RX − 8801 JE ( VSOJ − 20pin ) 9.2.1. External dimensions RX − 8801 JE ( VSOJ − 20pin ) • External dimensions • Recommended soldering pattern 10.Application notes 1)Notes on handling 2) Notes on packaging AMERICA EUROPE Distributor Electronic devices information on WWW server http://www.epsontoyocom.co.jp