SPECIAL USE FEATURES AND FUNCTIONS continued
E1 MANUAL
SPECIAL USE FEATURES AND FUNCTIONS continued
This control can also be used when the receiver is turned off. Press ‘CLEAR/LOCK’ for 3 seconds. A mes- sage will appear confirming lock. If power is then pressed, a “Press CLEAR/LOCK for 3 seconds to unlock” message will appear. The user must perform this action before the ‘POWER’ key will allow the receiver to be turned on.
BROADCAST BAND TUNING STEP SIZE
In the AM broadcast band, the E1 receiver increments the frequency in 10 kHz steps when pressing the ‘< SELECT >’ keys. The 10 kHz step size is practical for tuning the U.S. and Canadian broadcast bands. However, the step size can be changed to 9 kHz to permit practical tuning of European broadcast stations. The tuning step size is held in nonvolatile memory and thus is not lost during power failure or battery changing.
To select the alternate step size:
Press the ‘MENU’ softkey to activate the MAIN MENU. Then press ‘1' on the
“4 MW TUNING STEPS 9 / 10 kHz”
Pressing ‘4' on the
the ‘Direct-Key-Input’ keypad.
DELETE ALL MEMORY OR COUNTRY CHANNELS The following procedure will delete either all MEMORY or all COUNTRY channels.
•Place the receiver in either MEMORY or COUNTRY mode by pressing the ‘MEMORY’ or ‘COUNTRY’ softkeys.
•Press ‘POWER’ to power down the receiver.
•Press the ‘POWER’ key again and hold.
•While holding the ‘POWER’ key, press the ‘MEMORY’ or ‘COUNTRY’ softkey for two seconds.
•This will cause the message “DELETE PAGE ?” to appear on the display. You can now release the keys.
•If you hadn’t already pressed ‘MEMORY’ or ‘COUN- TRY’ you can do so now.
•While the “DELETE PAGE ?” message is still visible, press the ‘DELETE’ key for two seconds to delete the page.
Note that if the “DELETE PAGE ?” message disappears from the display before you press the ‘DELETE’ key, you
must start over.
DELETE ALL MEMORY AND COUNTRY CHANNELS If it is desired to delete all MEMORY AND COUNTRY channels in one operation, proceed as follows:
•Place the receiver in either MEMORY or COUNTRY mode by pressing the ‘MEMORY’ or ‘COUNTRY’ softkey.
•Turn the receiver off by pressing the ‘POWER’ key.
•Press and hold the ‘POWER’ key.
•Press the ‘DELETE’ key for two seconds while still holding down the ‘POWER’ key.
•This will cause the message “Are you really sure you want to delete the program information in all 1700 memory channels?” to appear.
•While this message is still displayed, press the ‘DELETE’ key for two seconds to clear MEMORY and CHANNEL memories.
DISPLAY LIGHTING
With AC Adapter
When the unit is operating from the external AC adapter or other DC power source and is turned OFF, the display lighting will revert to one of the following states.
•If Dim, Medium, or Bright was selected using the ‘LIGHT’ key when the unit was ON, the display will be Dim when the unit is turned OFF.
•If no backlighting was selected using the ‘LIGHT’ key when the unit was ON, the display will not be illuminated when the receiver is turned OFF.
•When the receiver is in the OFF state, the display illumination can be toggled on and off with the ‘LIGHT’ key. If toggled on, the illumination will remain on indefinitely.
Regardless of display lighting, the LCD display will remain ON, displaying the time indefinitely, and can be switched between Local and GMT time using the ‘TIME’ key.
With Batteries Only
When the receiver is turned OFF when operating from batteries the display lighting will do one of the following.
•If Dim, Medium, or Bright was selected using the ‘LIGHT’ key when the unit was ON, the display will be Dim when turned OFF, and will remain lit dis playing Local or GMT time for ten seconds, after which both the Dim lighting and the LCD “TIME” display will turn off.
•If no backlighting was selected using the ‘LIGHT’ key when the unit was ON, the display will not be illuminated when the receiver is turned OFF. The LCD display will show Local or GMT time for ten seconds and then turn OFF.
•Pressing the ‘LIGHT’ key when the receiver is OFF will cause the display illumination to be toggled between being on and off. The LCD display and any illumination will turn off after 10 seconds. When the unit is OFF, pressing the ‘TIME’ key once will activate the LCD “TIME” display and additional presses of the ‘TIME’ key will cycle the “TIME” display between Local and GMT. If any dis play illumination was selected when the unit was last in the ON state, Dim display lighting will be turned on with the first press of the ‘TIME’ key along with the LCD display. Both illumination and the LCD display will turn OFF ten seconds after the last press of the ‘TIME’ key. When the receiver is ON, and either Dim, Medium, or Bright backlighting is selected, the illumination will turn OFF ten seconds after the last control input. Changing any control setting other than ‘SQUELCH’, ‘TREBLE’, ‘BASS’, or ‘VOLUME’ will cause the display to come back ON and remain ON for ten seconds after the last control setting change and then turn back OFF. This “time out” feature can be disabled by holding down the
‘LIGHT’ key for three seconds. You will hear a confirming beep. This will cause the illumination to stay ON until the receiver is turned OFF. However, the user should keep in mind that this mode of operation will result in a considerable reduction in battery life. The illumination timeout feature can be
•Hold down the ‘LAMP’ key for three seconds. A beep will be heard, confirming that the feature has been enabled.
•Turn the receiver ‘POWER’ OFF and back ON.
46
47
