Manuals / Brands / Computer Equipment / Switch / Extron electronic / Computer Equipment / Switch

Extron electronic 325 Installing the firmware (prepare, activate, and commit stages)

1 78

Download 78 pages, 6.7 Mb

4. Click the Browse button (a). The File Upload window (see figure 44) opens.

2

2

3

1

Figure 44. Upload a Firmware File to the Controller Codec

5. Navigate to the folder where you saved the firmware upgrade file, select the file, and

click the Open button (b). The File Upload window closes.

6. On the upgrade page, click the upload button (c). The selected file is uploaded to a

temporary memory area in the controller. This can take a few moments.

A status bar at the bottom of the upgrade page shows the status of the

load. The status bar closes and the Upgrade Version field displays the new value.

The controller can hold a maximum of two upgrade files. If another is loaded then the

oldest file is deleted.

Installing the firmware (prepare, activate, and commit stages)

Once the file is uploaded, unpack and copy the new firmware (from the controller) into the

VNC 325 alternate flash memory of each unit, starting with the controller unit.

1. Open the upgrade page (see “Uploading (Copying the Upgrade to the Controller

Codec)“, steps 2 and 3, except select the codec on which you want to install the

upgrade, which may or may not be the controller codec.

2. Click the Select Firmware Version drop-down box (a on figure 45) and click the

firmware file you want to install. Usually only one is file listed.

1

2

Figure 45. Prepare an Upgrade in a Codec

VN-Matrix 325 Serial Digital Over IP CODEC • Operation 55

Contents

Main Caution Warning Attention Avertissement Safety Instructions English Consignes de Scurit Franais Sicherheitsanleitungen Deutsch Achtung Vorsicht FCC Class A Notice Conventions Used in this Guide Copyright Trademarks Contents Introduction ............................................1 Installation and Setup ............................ 5 Operation ...............................................31 Alarms and SNMP ..................................59 Page Introduction Page Features Page Installation and Setup Installation and Setup Overview Rear Panel Features a b c d e f g h Network Netw Page Page Example 1: Switched and isolated network configuration Page Example 2: Switched and isolated network configuration Page Example 3: Routed Network Configuration Configuring Network Settings Serial Port Wiring Low-level Network Configuration Page Configuration Selections Making Remaining Connections RS-232 Over LAN Port LAN Ports d e RJ-45 port wiring Video Input, Output, and Loop Connections Encoder configuration a b c Network Decoder configuration a b Configure Encoders and Decoders Startup and Login Page Configure the Units as Encoders or Decoders Page Page Enable multicast streaming Operation Indications and Controls a b c Network Interface Device List Page Device Field Device Mode Removing a device from the network Page Device summary panel Licensed features panel Device setup panel Configuration panel Configuration Page Video Encoder Streams panel Configuration Page Audio Encoder Name panel ANC (Audio) panel Forward error correction (FEC) panel Streams panel Configuration Page Colfec and Rowfec Encoders Bandwidth Management Page and Typical Bit Rates a b Bandwidth management standard controls panel Advanced Controls panel Typical bit rates Decoder Display and Configuration Page a b Decoder Video Configuration Panel Decoder Streams Configuration Panel Decoder Bit Rate and Stream Page a b c d e Dropped packets row Displays the number of data packets dropped during the G Page Configuring a Serial Pass-through Group Firmware Upgrade Page Uploading the upgrade to the controller codec Installing the firmware (prepare, activate, and commit stages) License Page Accounts Page (Passwords and Clock Management) Passwords Panel Clock Management Panel Controller Licensing Panel Alarms and SNMP Alarms Alarms Page Filter settings panel a b c d e Alarm list panel Alarm types and descriptions Page Alarm Logs page Simple Network Management Protocol SNMP Password Value Page Reference Information Specifications Video Video input and loop through encoder Video processing codec Sync genlock decoder Audio input and output NOTE: Audio processing Control host ports codecs, decoders Network transport General Specifications are subject to change without notice. Part Numbers and Accessories Codec Part Number and Included Parts Mounting and Power Options Optional SFP Module Cables Mounting the Codec Tabletop Use Mounting kits UL Rack-Mounting Guidelines Test Pattern Extron Warranty