Reference Information
Specifications
Video
Gain | Unity |
Number/signal type | 4 sets of proprietary analog signals |
Connectors | 4 female |
Video input and loop through — per transmitter
Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, |
| component video (with |
| |
| 1 buffered RGBHV, RGBS, RGsB, RsGsBs |
| local monitor loop through |
| (includes ID bits) |
Connectors | 2 female |
Nominal level | 1 |
| |
| 0.7 |
| component video |
| 0.3 |
Minimum/maximum levels | 0.3 V to 1.45 |
Impedance | 75 ohms |
Horizontal frequency | 15 kHz to 130 kHz |
Vertical frequency | 30 Hz to 150 Hz |
Return loss | |
DC offset (max. allowable) | 250 mV |
Video output — see receivers’ specifications | |
Sync |
|
Input type (transmitter) | RGBHV, RGBS, RGsB, RsGsBs, |
| |
Output type (receivers) | RGBHV, RGBS, RGsB, RsGsBs |
Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level (transmitter) | 3.5 V to 5.5 |
Output level (receivers) | 4.0 V to 5.0 |
Input impedance | 510 ohms |
Output impedance | 110 ohms |
Max. input voltage | 5.5 |
Polarity | Positive or negative |
Control/remote — external device
Serial control port input/output.
connector
Serial control port output/input. 1 set of proprietary signals on a female
NThe serial communications link of an MTP RL 15HD RS or
MTP RL 15 HD RS SEQ is unidirectional only, transmitter to receiver, unless the receiver’s directional jumper has been repositioned. The jumper should be repositioned only when the receiver is the only one in the system.
Baud rates | Up to 38400 bps at up to 600’ (183 m) |
| (Higher data rates and distances are |
| possible. Performance will vary based on |
| baud rate and cable length.) |
Protocol | Data bits = 5 - 8 |
| Stop bits = 1 or 2 |
| Parity = odd, even, none |
| Flow control = XON, XOFF, none |
NProtocol is mirrored between the transmitter and the receiver.
Serial control pin configurations. Captive screw connectors: 1 = TX, 2 = RX,
3 = GND
General
Power | 100 VAC to 240 VAC, 50/60 Hz, 20 watts, |
| internal |
Temperature/humidity | Storage: |
| 10% to 90%, noncondensing |
| Operating: +32 to +122 °F (0 to +50 °C) / |
| 10% to 90%, noncondensing |
Cooling | Convection, unvented |
Rack mount | Yes, with included mounting brackets, |
| part |
Enclosure type | Metal |
Enclosure dimensions | 1.7" H x 17.5" W x 8.5" D |
| (1U high, full rack wide) |
| 4.3 cm H x 44.4 cm W x 21.6 cm D |
| (Depth excludes connectors.) |
Product weight | 6.0 lbs (2.7 kg) |
Shipping weight | 10 lbs (5 kg) |
Vibration | ISTA 1A in carton |
| (International Safe Transit Association) |
MTP 4T 15HD RS • Reference Information | MTP 4T 15HD RS • Reference Information |