set-up and connections

Power Tower

In setting up the system, the Passport Mixing console should ideally be placed where system performance can be evaluated by the operator. If no ongoing adjustments will be necessary, the mixer may be placed conveniently and where the cable lengths allow.

specifications

Part Number

069-3001-000 PD-250+ 120V US

 

069-3001-900 PD-250+ 120V DS

 

069-3001-930 PD-250+ 240V AUS

 

069-3001-940 PD-250+

230V UK

 

069-3001-960 PD-250+

230V EUR

 

069-3001-970 PD-250+ 100V JPN

Take care to place the Power Tower where the cables will not trip anyone. All cables should be carefully secured.

The storage compartment in the rear of the Tower can hold cables, microphones and other system parts. To open simply slide the catch upwards and pull open.

The mains (AC) fuse holder is under the IEC (power cord) socket on the right rear of the Tower. To change a fuse, remove the IEC plug and, using an appropriate tool pull out the fuse holder. Note there is a spare fuse in the fuse holder; the Passport utilizes a T6.3AH, 250V fuse. Only replace fuses with one of an identical value and size.

The Passport System is weather resistant in

Frequency Response

Distortion

System Signal to Noise Ratio

Power Output

Input Impedance

(Channels 1-2-3-4 XLR and 1/4”)

(Phono and Stereo Channel 1/4”)

Max. Input Level

50 Hz to 30 kHz ± 1 dB (at speaker output) 30 Hz to 20 kHz ± 1 dB (at send output)

<0.5% 20 Hz to 20 kHz (at speaker output)

<0.1% 20 Hz to 20 kHz (at send output)

> 85 dB, “A” WTD

250 W (125 W/ch @ 8ohm per channel)

“Mic” switch position: 2 k ohm

“Line” switch position: 66 k ohm 78 k ohm

Mic:

-11 dBu

Line:

20 dBu

Stereo:

26 dBu

its packed transport mode. However, when operating outdoors, take care to fully protect the Power Tower in the event of exposure to rain.

Remember to allow free air flow through the air inlet located at the bottom of the rear panel on the Passport power tower.

Return Input Impedance

47k ohm

 

Fuse type

T6.3AH, 250V

Passport System

Width:

840 mm (33.7 in.)

 

Height:

615 mm (24.2 in.)

 

Depth:

300 mm (11.8 in.)

 

Weight:

24 kgs (53 lbs)

Speakers

Width:

300 mm (13.4 in.)

 

Height:

610 mm (24.2 in.)

 

Depth:

300 mm (11.8 in.)

 

Weight:

7.3 kgs (16 lbs)

Power Tower

Width

185 mm (7.3 in.)

 

Height

615 mm (24.2 in.)

 

Depth

300 mm (11.8 in.)

 

Weight

9.5 kgs (21 lbs)

Tower Footprint

350 x 300 mm (9.5 x 11.75 in.)

Microphone

Dynamic Cardioid, balanced

Microphone Cable

XL -Male to XL-Female, 6 m (20 feet)

Speaker Cables

1/4 in. to 1/4 in., 9 m (27 feet)

 

0 dBu is referenced to 0.775 volts rms

14

Page 14
Image 14
Fender PD250 Plus manual Specifications, Power Tower