First Alert FA168CPS, FA148CP manual

MISCELLANEOUS SYSTEM FIELDS (*174-*181)
✱174	CLEAN ME REPORTING OPTIONS	[0]
	(for ESL smoke detectors)
✱177	DEVICE DURATION 1, 2		[0] [0]
	(used in *80 Menu mode-Device Actions 5/6)
		1	2
✱181	50/60 HERTZ AC OPERATION	[0]
CONFIGURABLE ZONE TYPE OPTIONS (*182-*185)
✱182	CONFIGURABLE ZONE TYPE 90

0 = disable; 1 = Clean Me signal reports;

Note: If Clean Me is enabled, you must enter “3” in field ✱56 programming for zone 1 response time.

0	= 15 seconds	6	= 2-1/2 min	#+11 = 7 min
1	= 30 seconds	7	= 3 min	#+12 = 8 min
2	= 45 seconds	8	= 4 min	#+13 = 10 min
3	= 60 seconds	9	= 5 min	#+14 = 12 min
4	= 90 seconds	#+10 = 6 min		#+15 = 15 min
5	= 2 minutes
0	= 60 Hz; 1 = 50 Hz

1 2 3 4 5 6 7 8 9 10

Enter the appropriate value for each entry, 1-10, based on the charts provided on the next page. Each entry is the sum of the values of its selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

✱183 ZONE TYPE 90 REPORT CODES

IMPORTANT: Use existing Contact ID® codes, if appropriate, or define unique codes in CID code range 750-789. See important note in installation instructions.

90 ALARM ID: XXX TROUBLE ID: XXX

Enter the desired 3-digit Contact ID® report codes for alarms and troubles occurring on zones assigned to this zone type. Enter the codes sequentially (all 6 digits). When entering digits, [#] moves cursor back, [∗] moves forward. Press [∗] when done to continue.

✱184 CONFIGURABLE ZONE TYPE 91

✱185 ZONE TYPE 91 REPORT CODES

IMPORTANT: Use existing Contact ID® codes, if appropriate, or define unique codes in CID code range 750-789. See important note in installation instructions.

TOUCH SCREEN DEVICE (AUI) ENABLE

✱189 AUI DEVICE 1 and 2 ENABLE (for Touch Screen style keypads)

NOTE: System supports up to two touch screen style keypads (e.g. Symphony Advanced User Interface, and 6270 Touch Screen keypad).

1 2 3 4 5 6 7 8 9 10

Enter the appropriate value for each entry, 1-10, based on the charts provided on the next page. Each entry is the sum of the values of its selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

	91 ALARM ID: XXX		Enter the desired 3-digit Contact ID® report codes for
	TROUBLE ID: XXX		alarms and troubles occurring on zones assigned to
			this zone type. Enter the codes sequentially (all 6
			digits). When entering digits, [#] moves cursor back, [∗]
			moves forward. Press [∗] when done to continue.
		[1] [1]	Enter each touch screen (AUI) device’s home partition.
			0	= disabled
AUI 1 AUI 2
			1	= partition 1; 2 = partition 2; 3 = partition 3 (common)

AUI 1: Must set AUI address to 1	NOTE: A minimum of one standard keypad must also be
AUI 2: Must set AUI address to 2	installed when AUI is used. Use of AUI does not affect
(see Inst. Instr. for details)	the number of standard keypads supported.

KEYPAD OPTIONS *190-*196(NOTE: Options for keypad address 16 are set by the factory and cannot be changed.)

NOTE: Each keypad must be assigned a unique address. Keypads programmed with the same address will give unpredictable results.

✱190	KEYPAD 2 DEVICE ADDRESS 17		[0] [0]	Partition:	0 = keypad disabled; 1-3 = part. no. (3 = com)
				Sound:	0 = no suppression
		Partition/	Sound
					1 = suppress arm/disarm and E/E beeps
		Enable†			2 = Suppress chime beeps only
		†FA168CPS: enter partition			3 = suppress arm/disarm, E/E, and chime
		FA148CP:	1 = enable		beeps
			0 = disable
		Part./Enable†	Sound	See field ∗190 for entries.
✱191	KEYPAD 3 DEVICE ADDRESS 18		[0] [0]
✱192	KEYPAD 4 DEVICE ADDRESS 19		[0] [0]	See field ∗190 for entries.
✱193	KEYPAD 5 DEVICE ADDRESS 20		[0] [0]	See field ∗190 for entries.
✱194	KEYPAD 6 DEVICE ADDRESS 21		[0] [0]	See field ∗190 for entries.
✱195	KEYPAD 7 DEVICE ADDRESS 22		[0] [0]	See field ∗190 for entries.
✱196	KEYPAD 8 DEVICE ADDRESS 23		[0] [0]	See field ∗190 for entries.
✱197	EXIT TIME DISPLAY INTERVAL	[0]		0 = no display; 1-5 = seconds between display refresh
				NOTE: If enabled and using only 2-digit fixed-word
				keypads (e.g., FA245RF), do not set exit delay time
		[0]		greater than 96 seconds. See Inst. Instr. for explanation.
✱198 DISPLAY PARTITION NUMBER				0 = no; 1 = yes (partition no. appears on Alpha Display)
	(FA168CPS; for Alpha Display Keypads)			0 = 3-digit display (“1” + device address)
✱199	ECP FAIL DISPLAY	[0]
				1 = 2-digit fixed-display as “91”

– 7 –