Fisher & Paykel GW512, GW612, GW712, MW512, MW612 Inlet Hoses, Levelling

5

Installation Instructions

Inlet Hoses

1

Connect the straight ends of the inlet hoses to the taps. There are

washers fitted in both ends.

2

Connect the elbow ends of the inlet hoses to the machine inlet

valves. Inlet valves are marked on the back of the machine

H=Hot C=Cold.

Cold supply only:

If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the

hot inlet valve. The cap prevents water leaking out of the hot valve. The cap is available from your

Fisher & Paykel Dealer or Authorised Service Centre, Part No. 388491. This appliance incorporates

backflow protection complying with AS3500.1. No further backflow protection is required for

connection to the water supply.

Levelling

It is IMPORTANT to level the machine to ensure even spin

performance.

1

Separate the 4 rubber foot inserts from the moulding and

fit into the feet on the base of the machine.

2

Move the machine to its final position. (We suggest a

minimum clearance of 20mm each side).

3

Adjust the feet so the machine is level and cannot rock.

To check if your machine is level:

Look down on the wash bowl and make sure it sits slightly forward of centre (see Diagram 1).

Close the lid. Visually check that the lid fits evenly on both sides. If it does not look like the

diagram in the middle, adjust one of the front feet slightly until it matches. The diagram on the

top and bottom are not correct (see Diagram 2).

4

Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses.

5

Uncoil power cord and plug into wall socket.

Adjustable feet

Rubber insert

Tap end

To check levelling look

down on the wash bowl

Correct

Incorrect

Diagram 1

Lid Alignment

Lid

Topdeck

Wind right foot down

(out) to correct

Wind left foot down

(out) to correct

Lid

Lid

Topdeck

Topdeck

Diagram 2

Machine end

Contents

Main Intelligence Working For You Contents Please Note: Unpacking Removing the Packaging Drain Hose To prevent syphoning: Inlet Hoses Cold supply only: Levelling To check if your machine is level: Water Supply CAUTION! Accessories and Spare Parts Hot N Safe Valves Available Are: Before You Do Your First Wash Using Your Excellence Washer A. Detergent GW712, GW612, GW512 C D F E Using Your Pride Washer A. Detergent MW612, MW512 C D E F Lidlock Wash Cycles and Options Default Settings Model Variations Wash Options and Advancing the Cycle To S elect the Wash Options Model The Wash Progress Lights To Advance the Wash Cycle Water Levels Manual Water Level Selection Auto Water Level Wash Options Saving Water Eco & Models Water Saver Model Only Wash Options Soak Nappy Sanitisers/ Bleach Spin Hold Delay Start Wash Options Washing Bulky Items Washing Woollens Favourite Cycle Favourite Cycle To S et Your Favourite Cycle To U se Your Favourite Cycle Customising the Wash Cycles To C ustomise a Cycle Before You Wash Sorting Loading Detergent Choosing The Right Detergent How Much Detergent? Adding the Detergent Tablets: Fabric Softener How the Fabric Softener is Dispensed How Much Fabric Softener? Cleaning the Dispenser Scrud Option Adjustment Mode To Enter Option Adjustment Mode Page Wash Temperatures Rinse Options Controlled Cold End of Cycle Beeps Water Saver Auto Water Fill Level Light on Option Out-of-Balance Recovery Routine Automatic Recovery Option Machine Stops Option Specifications Model Capacity Depth Width Height* Height (Lid Open) When You Have Finished Cold Water Washing Cleaning Your Smart Drive Cleaning the Inside of Your Smart Drive Products That Might Damage Your Smart Drive Smart Drive Sounds and Beeps Automatic Lint System Water Consumption Litres Per Cycle Saving Water Recycling the Wash Water Models Only Recycling the Water From Deep Rinse Saving Water Manual Suds Save With Syphon Back If Your Smart Drive Beeps for Help Musical Series of Beeps* Every 5 Seconds and... Possible Solutions HOT water temperature light is flashing. COLD water temperature light is flashing. HOT and COLD water temperature lights are flashing. If Your Smart Drive Beeps for Help LIDLOCK light is flashing. First RINSE or SPIN light is flashing as well as the Spin Speed light. Single Beep Every Second and... Possible Solutions Some lights are on but the pattern of lights is unfamiliar. Operating Problems Wash Problems Listed below are possible causes and solutions to some common wash problems. Creasing. Poor Soil Removal. Linting. Customer care In New Zealand If You Need Assistance...* If you need service...* In Australia If You Need Assistance...* If you need service...* Manufacturers Warranty Fisher & Paykel Undertakes To This Warranty Does Not Cover Note: