Fisher & Paykel GW512, GW612, GW712, MW512, MW612 CAUTION!

6

Installation Instructions

Water Supply

For best operating conditions your hot water

should be approximately 65˚C. Your cold water

should not exceed 35˚C or your hot water exceed

75˚C. Temperatures above these may cause the

machine to fault or cause damage to the machine.

If you have an uncontrolled water heating source

(eg a wet back or solar heating system) you should

fit a Safe Valve. This will ensure the hot water

temperature remains within safe limits.

Inlet water pressure: Max.1MPa (150 psi) Min. 34Pa (5 psi)

Inlet water flow rate: Min. 3 litres/min

Minimum height of taps to clear the top of the machine is 1150mm.

Draining

Regularly check that your standpipe or tub is free from lint or other obstructions, which may

affect how your machine works or may cause flooding.

In multi-storey apartments or any upper floor, the machine should be installed on a drained floor.

Draining must comply with local by-laws.

Autowasher Safety

This autowasher is not intended for use by young children or infirm persons without supervision.

Your Smart Drive® can now be opened while it is filling and agitating, supervise young children

to ensure they do not play with it.

CAUTION!

If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet

box), ensure that it is positioned so that it does not come into contact with water or moisture.

Accessories and Spare Parts

Available from your Fisher & Paykel Dealer or Authorised Service Centre.

Inlet Valve Cap Part No. 388491

Hose Inlet Long (2m) Part No. 422680

Hose Inlet Large Bore Part No. 426123

Drain Hose Extension Part No. 425627p

Power Cord If the Power Cord of your autowasher is damaged it must be

replaced by a Fisher & Paykel Authorised Service Centre, as it is not a

standard power cord.

Hot ‘N’ Safe Valves Available Are:

RMC TVA 50HF

RMC TVA 75HFS

Adjustable between 35˚C – 55˚C

RMC TVA 50HP

For instantaneous gas hot water supply

Contents

Main Intelligence Working For You Contents Please Note: Unpacking Removing the Packaging Drain Hose To prevent syphoning: Inlet Hoses Cold supply only: Levelling To check if your machine is level: Water Supply CAUTION! Accessories and Spare Parts Hot N Safe Valves Available Are: Before You Do Your First Wash Using Your Excellence Washer A. Detergent GW712, GW612, GW512 C D F E Using Your Pride Washer A. Detergent MW612, MW512 C D E F Lidlock Wash Cycles and Options Default Settings Model Variations Wash Options and Advancing the Cycle To S elect the Wash Options Model The Wash Progress Lights To Advance the Wash Cycle Water Levels Manual Water Level Selection Auto Water Level Wash Options Saving Water Eco & Models Water Saver Model Only Wash Options Soak Nappy Sanitisers/ Bleach Spin Hold Delay Start Wash Options Washing Bulky Items Washing Woollens Favourite Cycle Favourite Cycle To S et Your Favourite Cycle To U se Your Favourite Cycle Customising the Wash Cycles To C ustomise a Cycle Before You Wash Sorting Loading Detergent Choosing The Right Detergent How Much Detergent? Adding the Detergent Tablets: Fabric Softener How the Fabric Softener is Dispensed How Much Fabric Softener? Cleaning the Dispenser Scrud Option Adjustment Mode To Enter Option Adjustment Mode Page Wash Temperatures Rinse Options Controlled Cold End of Cycle Beeps Water Saver Auto Water Fill Level Light on Option Out-of-Balance Recovery Routine Automatic Recovery Option Machine Stops Option Specifications Model Capacity Depth Width Height* Height (Lid Open) When You Have Finished Cold Water Washing Cleaning Your Smart Drive Cleaning the Inside of Your Smart Drive Products That Might Damage Your Smart Drive Smart Drive Sounds and Beeps Automatic Lint System Water Consumption Litres Per Cycle Saving Water Recycling the Wash Water Models Only Recycling the Water From Deep Rinse Saving Water Manual Suds Save With Syphon Back If Your Smart Drive Beeps for Help Musical Series of Beeps* Every 5 Seconds and... Possible Solutions HOT water temperature light is flashing. COLD water temperature light is flashing. HOT and COLD water temperature lights are flashing. If Your Smart Drive Beeps for Help LIDLOCK light is flashing. First RINSE or SPIN light is flashing as well as the Spin Speed light. Single Beep Every Second and... Possible Solutions Some lights are on but the pattern of lights is unfamiliar. Operating Problems Wash Problems Listed below are possible causes and solutions to some common wash problems. Creasing. Poor Soil Removal. Linting. Customer care In New Zealand If You Need Assistance...* If you need service...* In Australia If You Need Assistance...* If you need service...* Manufacturers Warranty Fisher & Paykel Undertakes To This Warranty Does Not Cover Note: