Fluke 1521 - page 11

Chao Yang District

Beijing 100004, PRC

CHINA

Phone: +86-10-6-512-3436

Telefax: +86-10-6-512-3437

E-mail:xingye .han@fluke.com.cn

Fluke South East Asia Pte Ltd.

FlukeASEAN Regional Office

Service Center

60 Alexandra Terrace #03-16

The Comtech (Lobby D)

118502

SINGAPORE

Phone: +65 6799-5588

Telefax: +65 6799-5588

E-mail:antng @singa.fluke.com

When contacting theseService Centers for support, please have the following

information available:

•Model Number

•Serial Number

•Voltage

•Complete description of the problem

1 Before You Start

Authorized Service Centers

Contents

Main Rev. 571203 Table of Contents 7 Display Functions. . . . . . . . . . . . . . . . . . . . . . . . . 25 8 Communications Interface. . . . . . . . . . . . . . . . . . . . 37 9 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 10 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Page Figures and Tables 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 Warnings 1.2.2 Cautions 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 9 3 Specifications and Environmental Conditions Specifications 3.2 Environmental Conditions 4 Quick Start 4.1 Unpacking 4.2 Use Proper Care with the 1521 and Accessories 4.3 Learn About the Features and Components 4.4 Connect the Probe 4.5 Connect the Power Source 4.6 Switch the Power On 4.7 Measure Temperature Page Page 5.2 Top and Side Features 5.3 Back Features 5.4 Internal Features 5.5 Accessories Page 6 General Operation 6.1 Battery 6.2 DC Power Source + 6.3 Power Button 6.4 Display and Backlight 6.5 Probe 6.6 INFO-CON Connector 1521 Handheld Thermometer Readout Figure6 Probe Wiring Diagrams 24 7 Display Functions Each of these operating modes is described in the sections that follow. 7.1 Blank Mode This mode is identified by Blank that temporarily appears on the display. 7.2 Min/Max Mode 7.3 Hold Mode 7.4 Delta(x) Mode 7.5 Units 7.6 Rate 7.7 Resolution 7.8 CAL MODE 7.8.1 Mtr Due 7.8.2 Prb Due 7.8.3 Time 7.8.4 Passcode 7.8.5 Date 7.8.6 Probe Lock 7.8.7 Prb # 7.8.8 Prb Type 7.8.9 ITS-90 7.8.10 IEC751 7.8.11 CVD 7.8.12 YSI-400 7.8.13 THERM 7.8.14 Probe Wires 7.8.15 PCal 7.8.16 PDue 7.8.17 Filter 7.8.18 MCal 7.8.19 MDue 7.8.20 CAL1 and CAL2 8 Communications Interface 8.1 RS-232 Connection 8.2 Communication Command List 8.2.1 Primary Commands 8.2.2 Calibration Commands 39 8 Communications Interface Communication Command List Page Page 9 Calibration 9.1 Required Equipment 9.2 Calibration Procedure Page 10 Maintenance 11 Troubleshooting 11.1 An Error Message Is Displayed The followingtable lists possible error messages, their causes, and suggested actions. 47 11 Troubleshooting An Error Message Is Displayed 11.2 CE Comments 11.2.1 EMC Directive 11.2.2 Low Voltage Directive (Safety)