Manuals / Fluke / Computer Equipment / Network Card

Fluke 2686A, 2680A manual IP address display for setting an IP0 digit for example

Models: 2686A 2680A

1 74

Download 74 pages 62.55 Kb

Page 21

Getting Started

Configuring the 268XA

SET

IP address display for setting an IP:0 digit (for example, 129:196:152:101)

SET

IP address display for setting an IP:1 digit (for example, 129:196:152:101)

SET

IP address display for setting an IP:1 digit (for example, 129:196:152:101)

SET

IP address display for setting an IP:2 digit (for example, 129:196:152:101)

SET

IP address display for setting an IP:3 digit (for example, 129:196:152:101)

Figure 4 Examples for Reviewing and Setting General Network Parameters (cont)

11

Image 21

Fluke 2686A, 2680A manual IP address display for setting an IP0 digit for example

Contents

2680A/2686A Limited Warranty and Limitation of Liability Interference Information Safety InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Additional Safety Information SpecificationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Introduction Getting StartedAdditional Information Contacting FlukeConfiguring the 268XA Reviewing and Setting the Base Channel NumberReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary display Reviewing and Setting the Subnet Mask and Default GatewayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Host Computer and Network Preparation Installing Host Computer Ethernet AdapterPreparing for Network Operation SoftwareHost Computer/Device Direct Connection Device and Host Computer InterconnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters To install Fluke DAQ software on your computer Installing Fluke DAQ SoftwareInstalling Fluke DAQ Software Using the Toolbar Understanding the User InterfaceFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Device Status Icon Checking Operational StatusModule Status Icon Computed Channel Status IconConfiguration Dialogs Network Configuration DialogDevice Configuration Dialog Analog Channel Configuration Dialog Module Configuration DialogDIO Configuration Dialog Computed Channel Configuration DialogSecurity Dialogs Communication DialogsAlarm Dialog Mail and Web Settings DialogsTrend Dialog Managing Your Network Using Fluke DAQ Inserting and Configuring a 268XA DeviceTo insert and configure a device Group is externally wired Configuration fileAdvanced Setting autodisable scan Interval 3 autoscan rate Network TypeTreeView panel, select the device you just added Temperature Units Configuration transferIP Address Verify ButtonScan Parameters Monitor ChannelScan Overflow Log to PC Card 2686A onlyTo insert and configure a module Inserting and Configuring a ModuleModule Number Module TypeAlg109s.bmp Interval Trigger Alarm TriggerExternal Trigger Drift CorrectionStart Count DebounceDirection To insert and configure a Channel Inserting and Configuring a ChannelCH # Alarm TypeLabel Unit LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Digital Output Use Channel as Alarm TriggerTrigger Scan With Module Channel a or Channel BUsing Equations with Computed Channels Alg120s.bmp Starting a Configuration Scan To start a configuration scanStarting a Scan To start a device scan Starting a Device ScanTo start a Spy scan Starting a Scan Using SpyTo view module measurement data Viewing Module Measurement DataTo view digital I/O points dialog Using the Digital I/O Points Communication DialogTo use the trend feature Using Trend to View Collected DataType PenZoom ExportModule Device IDStart Date/Start Time DurationTo change the strip chart display Changing the Chart DisplayTo view alarms Viewing AlarmsAlarm Device Filters AckPeriod of Viewing To use the system security feature Using Fluke DAQ System Security FeaturesTo enter web and alarm mail settings Configuring Web and Alarm Mail SettingsUpdate Send alarms by e-mailData Server IP Address Uniform Resource Locator URL