Setting Surface Controls
Models with Ceramic Glass Cooktop (Some models)
About the Ceramic Glass Cooktop
The ceramic cooktop has radiant surface elements located below the surface of the glass. The design of the ceramic cooktop outlines the area of the surface element underneath. Make sure the diameter of the pan matches the diameter of the element outline on the cooktop (See Figure 1).
Heat is transferred up through the surface of the cooktop to the cookware. Only
About the Radiant Surface Elements
The element temperature rises gradually and evenly. As the temperature rises, the element will glow red. To maintain the selected setting, the element will cycle on and off. The heating element retains enough heat to provide a uniform and consistent heat during the off cycle. For efficient cooking, turn off the element several minutes before cooking is complete. This will allow residual heat to complete the cooking process.
Locations of the Radiant Surface Elements and Controls
Element Configuration, appearance and graphics of cooktops may be different
|
|
|
| OFF |
|
|
| Small |
|
|
| Large |
|
|
|
| hi |
|
| Petit |
|
|
| Grand | |
|
|
|
|
|
|
|
|
|
|
|
| |
sim |
| sim |
|
| sim |
|
| 6 |
|
|
| 6 |
2 | 8 | 2 | 8 | lo | 2 |
| 8 |
|
|
| ||
|
|
|
|
|
| |||||||
3 | 7 | 3 | 7 |
| 3 |
| 7 | 4 |
|
|
| 4 |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
| . |
|
|
| . |
4 | 6 | 4 | 6 |
| 4 | 6 |
| 2 . |
|
| . 2 | |
|
| . | . | |||||||||
|
| . | . |
| ||||||||
|
|
|
| med |
|
|
|
| .. | . |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Your appliance is equipped with radiant surface elements with different wattage ratings. The ability to heat food quicker and in larger volumes in- creases as the element wattage increases.
The example shown (figure 1) describes a model with all kind of elements you could possibly have, but the element configuration, the appear- ance and graphics of your cooktop may be different.
NOTE: Due to the high intensity of heat generated by the surface ele- ments, the glass surface will turn green when the element will be turned off. This phenomenon is normal and the glass will come back to its original white color after it has completely cooled down. (White glass
cooktops only).
Warmer Zone Element (some models) - Figure 1
NOTE: Please read detailed instructions for ceramic glass cooktop cleaning in the General Care & Cleaning section and Before You Call checklist section of this Use and Care Guide.
NOTE: Radiant elements have a limiter that allows the element to cycle on and off, even at the HI setting. This helps to prevent damage to the ceramic smooth top. Cycling at the HI setting is normal and can occur if the cookware is too small for the radiant element or if the cookware bottom is not flat (Refer to page 12 under Selecting Surface Cooking Utensils).
Element On & Hot Surface Indicator Lights
Your range is equipped with two different types of radiant surface control indicator lights that will glow on your range— the Element On indicator light and the Hot Surface indicator lights (See Figure 2).
The Element On indicator lights are located on the control panel above each radiant element control knob and will glow when a surface element is turned ON. A quick glance at this indicator light after cooking is an easy check to be sure ALL surface controls are turned OFF. The Hot Surface indicator light located on the control panel will glow when any surface cooking area heats up and will REMAIN ON until the glass cooktop has cooled to a MODERATE level.
sim
2
3
4
Hot Surface
Surface Chaude
8
7
6Figure 2
NOTE: Radiant elements have a limiter that allows the element to cycle ON and OFF, even at the HI setting. This helps to prevent damage to the ceramic smoothtop. Cycling at the HI setting is normal and will occur more often if the cookware is too small for the radiant element or if the cookware bottom is not flat.
7