Service Procedures, Cleaning, Introduction

6.On BKSDU units, the built-in heater may be connected to a grounded 120VAC or 240VAC receptacle to prevent shortening from solidifying in the tank when immediate transfer to a disposal container is not possible.

2.4 Cleaning

Clean the crumb screen with a solution of detergent and water. Clean the exterior surfaces of the SDU with a soft cloth and a solution of detergent and water. It is not necessary to clean the interior of the reservoir, but if desired it may be wiped down with clean paper towels to remove excess residual shortening.

WARNING

DO NOT clean the interior of the reservoir with water or detergent. Introduction of water or detergent into the unit will permanently damage the pump.

3.SERVICE PROCEDURES

3.1 Introduction

Other than routine cleaning and the replacement of worn suction tube O-rings, the SDU is maintenance free. After long use, the pump vanes and pump shaft seal may require replacement due to wear. Frymaster recommends worn pump vanes and/or pump shaft seals be replaced by an FASC, but store personnel may perform these service actions without voiding the warranty.

3.2 Replacing Worn or Damaged O-Rings

If pump efficiency degrades, it is likely that the O-rings on the suction tube are worn or damaged. To replace the O-rings, follow the steps below.

1.Lift the pump assembly straight up and out of the handle assembly.

2.Remove the worn or damaged O-rings from the grooves at the bottom of the suction tube and replace with new O-rings. Apply Accrolube with Teflon grease or equivalent to bottom 2 inches of the suction tube.

3.Insert the suction tube through the tube bracket in the handle and into the receiver on top of the reservoir. Push down on the pump assembly to make sure the suction tube is fully seated.

3.3 Replacing Worn Pump Vanes and/or Pump Shaft Seal

Depending upon the amount of use, the vanes in the pump assembly will eventually wear, reducing the efficiency of the pump. The pump shaft seal can also become worn and start to leak. A kit for replacing the vanes and the seal is available. The pump shaft seal can also be purchased as a separate item. To replace the pump vanes, and/or the pump shaft seal, follow the steps below (refer also to the illustration on Page 6).

1.Loosen the setscrew securing the pump handle to the pump shaft and slip the handle off the shaft. If unit is a BKSDU remove the eight screws that secure the pump cover in place and remove the cover.

SDU50, SDU90, BKSDU specifications

Frymaster has established itself as a leader in commercial frying equipment, and its SDU series, including the SDU 50, SDU 90, SDU 100, and BKSDU, exemplifies the brand's commitment to innovation, efficiency, and quality. These fryers are designed to meet the diverse needs of various establishments, from small restaurants to large-scale kitchens.

The Frymaster SDU 50 is a compact fryer that is perfect for establishments with limited kitchen space. It offers a 50-pound oil capacity, making it suitable for businesses that require moderate production levels. This model features advanced technology that allows for consistent frying results, ensuring that foods are cooked perfectly every time. Additionally, the SDU 50 incorporates a digital control system, which enables precise temperature management and easy operation.

Moving up the scale, the SDU 90 provides significantly increased frying capabilities with its 90-pound oil capacity. This fryer is designed to handle higher volumes of food while maintaining critical cooking temperatures. The SDU 90 features built-in filtration systems that promote oil longevity and improve food quality. This model also includes energy-efficient heating elements, which help reduce energy consumption without sacrificing performance.

The SDU 100 offers the highest capacity in the series with a 100-pound oil capacity, making it ideal for large kitchens that require high-volume output. Like its counterparts, the SDU 100 is equipped with advanced temperature control technology and a robust filtration system, ensuring that oil quality remains high throughout prolonged use. This model minimizes the downtime associated with oil changes, significantly improving productivity.

The BKSDU is a specialized model designed for versatile cooking options, including pressure frying capabilities. It boasts advanced features that include programmable controls and multiple frying modes, catering to various cooking styles and menu items. The BKSDU is particularly useful for establishments that require varied cooking techniques, ensuring that the food is cooked to perfection every time.

Each fryer in the SDU series is constructed with durability in mind, utilizing high-quality stainless steel to withstand the demands of a busy kitchen. They also prioritize safety with features such as electronic ignition systems and automatic shut-off capabilities. Additionally, the ergonomic design of these fryers allows for ease of use and maintenance.

In summary, the Frymaster SDU series combines cutting-edge technology, efficient design, and robust construction to offer reliable performance for all frying needs. Whether opting for the compact SDU 50, the more substantial SDU 90, the high-capacity SDU 100, or the versatile BKSDU, these fryers are designed to elevate the frying experience in any commercial kitchen.

Frymaster SDU50 Service Procedures, Cleaning, Introduction, Replacing Worn or Damaged O-Rings

Models: SDU50 SDU90 BKSDU