9998
The image is blurred.
There is speckling on
the image.
The camera does not
emit any sound.
Frame erase does not
erase the frame.
The ERASE ALL
function does not erase
all the frames.
There is no image or
sound on the TV.
When the camera is
connected to a
computer, the
photography or playback
screen appears on the
camera’s LCD monitor.
Nothing happens when
I use the camera
switches.
The camera no longer
works correctly.
iThe lens is dirty.
iYou photographed scenery with Macro
mode selected.
iYou took a close-up shot without
selecting Macro mode.
iYou are shooting a subject that is not
suited to autofocusing.
The shot was taken with a slow shutter
speed (long exposure) in a high-
temperature environment.
iThe camera volume is set too low.
iThe microphone was blocked during
shooting/recording.
iThere is something covering the speaker
during playback.
Some frames may be protected.
iAn A/V cable was connected during
movie playback.
iThe camera is not connected to the TV
correctly.
i“TV” is selected as the TV input.
iThe TV volume is turned down.
iThe USB cable (included) is not properly
connected to the computer or camera.
iThe PC is not switched on.
iCamera malfunction.
iThe battery is exhausted.
The camera has suffered an unforeseen
problem.
iClean the lens.
iCancel Macro mode.
iSelect Macro mode.
iUse AF/AE lock to take the shot.
This is a characteristic of CCDs and does
not indicate a camera fault.
iAdjust the volume.
iTake care not to block the microphone
during shooting/recording.
iEnsure that the speaker is uncovered.
Remove the protection.
iAfter the movie playback mode is
stopped, connect the camera and TV
correctly.
iConnect the camera and TV correctly.
iSet the TV input to “VIDEO”.
iAdjust the volume.
iSet up the camera and the USB cable
(included) correctly.
iSwitch the PC on.
iBriefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power
adapter and try again.
iLoad a new fully charged battery.
Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again. If the error message is still
displayed, contact your FUJIFILM dealer.
Troubleshooting Possible causes Solutions
Troubleshooting eIf you think the camera is faulty, check the following once more.
The self-timer lamp
does not light when
charging the battery.
The self-timer lamp
blinks during charging
and the battery won’t
charge.
No power.
Power cuts out during
operation.
Battery runs out quickly.
No photograph is taken
when the Shutter button
is pressed.
Can’t use the flash to
take pictures.
The flash settings are
restricted and cannot
be selected.
Can only select
“Suppressed Flash”
flash mode.
The “Q” or “5” quality
modes cannot be
selected.
The photographed
image is dark even
though the flash was
used.
iThere is no battery in the camera.
iThe camera and AC power adapter are
not connected correctly.
iThe battery terminals are dirty.
iThe battery is faulty or flat.
iThe battery is exhausted.
iThe AC power adapter plug has come
out of the power outlet.
iThe battery is loaded the wrong way
round.
iThe battery cover is not closed properly.
The battery is exhausted.
iCamera is being used in extremely cold
conditions.
iThe terminals are soiled.
iThe battery is flat.
iNo xD-Picture Cardis inserted.
iThe xD-Picture Cardis fully recorded.
iThe xD-Picture Cardis not formatted.
iThe xD-Picture Card contact area is
soiled.
iThe xD-Picture Cardis damaged.
iThe Auto Power Off function has
switched the camera off.
iThe battery is exhausted.
iThe Shutter button was pressed while
the flash was charging.
iThe flash is not popped up.
iThe camera is set to Scenery in Scene
Position mode.
iContinuous shooting is selected.
Scene Position mode is selected.
Continuous shooting is selected.
The sensitivity is set to 800 (high-sensitivity
shooting).
iThe subject is too far away.
iYour finger was covering the flash/flash
control sensor.
iLoad the battery.
iConnect the camera and AC power
adapter correctly.
iTake the battery out briefly and then
reload it.
iWipe the battery terminals with a clean,
dry cloth.
iFit a new battery. If the battery still fails
to charge, contact an authorized
FUJIFILM service center.
iLoad a fully charged battery.
iPlug the adapter back in.
iLoad the battery in the correct direction.
iClose the battery cover properly.
Load a new fully charged battery.
iPut the battery in your pocket or another
warm place to heat it and then load it
into the camera just before you take a
picture.
iWipe the battery terminals with a clean,
dry cloth.
iFit a new battery.
iInsert an xD-Picture Card.
iInsert a new xD-Picture Card or erase
some unwanted frames.
iFormat the xD-Picture Card.
iWipe the xD-Picture Card contact area
with a clean dry cloth.
iInserta new xD-Picture Card.
iSwitch the camera on.
iLoad a new fully charged battery.
iWait until charging is completed before
pressing the Shutter button.
iPop up the flash.
iSelect another Scene Position or change
the photography mode.
iSet continuous shooting to “OFF”.
The flash settings are restricted because
the camera settings are tailored to the
scene being shot. Change the
photography mode for a wider range of
flash settings.
Set continuous shooting to “OFF”.
In the Photography menu, set the
sensitivity to 400 or less.
iMove to within the effective flash range
before taking the shot.
iHold the camera correctly.
Troubleshooting Possible causes Solutions