fi-6010N Network Scanner Getting Started

3. Set the scanner's IP address. This may be

done automatically, by pressing the DHCP [On]

button.

The IP address may also be set manually, by

pressing the DHCP [Off] button and entering

the following numerical addresses:

IP Address

3.6 Setting the Admin Network

Set the network settings for connecting to a scanner from the Admin Tool or Central Admin Server.

1.

 

Select the [Network Settings] tab on the top

 

 

menu.

2.

 

Select the [Admin Network] tab on the left side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Select whether or not to enable SSL.

Select the [On] button enables SSL. If SSL is enabled, press the [Regenerate] button to create another SSL Certificate. When a new SSL Certificate is created, the contents of the certificate are changed. The contents of the SSL Certificate are as follows.

3.Enter the following numerical addresses:

•Primary DNS

•Secondary DNS

If a DNS server setting is not required, enter "0.0.0.0".

•

 

•

Subnet Mask

•

Default Gateway

menu.

• Issued by

Displays the SSL Certificate issuer.

• Valid from

Displays the SSL Certificate expiration date. The expiration date is five years from the date on which the certificate was created. This is shown in date form.

Selecting the [Off] button disables SSL.

5.Press the [OK] button.

⇒The communication settings are set.

ATTENTION

The following settings combinations

are not possible.

 

ATTENTION

HINT

the scanner is not

A Secondary DNS cannot be set without a Primary DNS.

DNS Dynamic Update and DNS Suffix can also be set.

The current FQDN is shown for the FQDN. However, if

connected to the network, the FQDN may not be displayed correctly.

4.Press the [OK] button.

⇒The information entered is set.

 

If the IP address is the same as one

HINT

already in use, network communica-

 

 

tion problems will occur. In this case,

 

try the following steps:

 

 

1. Disconnect the LAN cable, press

 

 

the [Shutdown] button on the

 

 

touch panel, and turn the scan-

 

 

ner off.

 

 

2. Reboot the scanner with the

 

 

LAN cable still disconnected,

 

 

and enter a non-duplicate IP

 

 

address.

 

 

3. Re-connect the LAN cable to the

 

 

scanner.

 

When DHCP is set to "On", the follow-

 

ing settings are assigned by the

 

DHCP:

 

•

IP Address

 

•

Subnet Mask

 

•

Default Gateway

 

•

DNS Server

 

•

WINS Server

⇒The "Admin Network" screen appears.

3.Enter a port number from 1 to 65535, to be used by the scanner to communicate with the Admin Tool or Central Admin server.

The default setting is 80.

ATTENTION

• Port numbers 135, 139, 445, and

numbers from 1025 to 1124, cannot

 

be specified as they are already

 

reserved in the scanner.

 

• If port numbers other than

 

HTTP:80, HTTPS:443 are to be

 

specified, it is recommended that

 

numbers over 5000 are used. If a

 

port number lower than 5000 is

 

specified, verify the Admin Tool

 

connectivity with the port number

 

first.

•Port Number "80" and SSL "On"

•Port Number "443" and SSL "Off"

Continue with the DNS settings.

3.7 Setting the DNS Server

A primary DNS and secondary DNS can be set.

1.Select the [Network Settings] tab on the top menu.

2.Select the [DNS Server] tab on the left side menu.

4.Press the [OK] button.

⇒The information entered is set.

Continue with the WINS settings.

3.8 Setting the WINS Server

A primary WINS and secondary WINS can be set.

1.Select the [Network Settings] tab on the top menu.

2.Press the [ ] button on the left side menu.

⇒Scroll the left side menu down until the [WINS Sever] tab appears.

3.Select the [WINS Server] tab on the left side menu.

• Domain Suffix

Even if DNS or WINS server is set, pri-

ority is given to the scanner settings over the DHCP settings.

⇒The "DNS Server" screen appears.

⇒ The "WINS Server" screen appears.

Continue with the connection settings.

9

10