5. Enter the password. Password is case sensitive. Enter "password" here.
6. Press the [Login] button.
⇒ If the administrator name and password are valid, the "System Settings" screen appears.
3.2 Changing the Administrator Password
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ATTENTION |
|
| If you change the password, save | |||||||||||||||||||||||||||||
|
| the new password in a safe location. | ||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
| If you lose the password, contact | |||||||||||||||||||||||
|
|
|
|
|
|
|
|
| your FUJITSU scanner dealer or an | |||||||||||||||||||||||
scanner service |
|
| authorized FUJITSU | |||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
| provider. This may incur a cost to | |||||||||||||||||||||||
|
|
|
|
|
|
|
|
| reset the scanner. | |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The administrator password can be changed.
1.Select the [System Settings] tab on the top menu.
2.Press the [
] button on the left side menu.
⇒Scroll the left side menu down until the [Admin Password] tab appears.
3.Select the [Admin Password] tab on the left side menu.
4.Enter the "Current Password", "New Pass- word", and "Confirm New Password".
Passwords must be between 7 and 127 characters long.
Alphanumeric characters (case sensitive) and symbols may be entered.
5.Press the [OK] button.
⇒The new admin password is set.
3.3Setting the Scanner Name
A scanner name may be set to provide a network alias for the device.
ATTENTION | Do not use a name that is already |
being used in the network. | |
| Name duplication will cause a net- |
| work connection error. |
1.Select the [System Settings] tab on the top menu.
2.Select the [Scanner Name] tab on the left side menu.
⇒The "Scanner Name" screen appears.
3.Enter a scanner name.
Scanner names may be up to 15 characters long. Use only alphanumeric characters (case sensitive) and hyphens.
Scanner names cannot consist of numerical characters only.
A hyphen cannot be used as the first character of a scanner name.
|
| The scanner can be setup to be a |
HINT |
| workgroup or domain member. |
|
|
|
|
|
|
4.Press the [OK] button.
⇒The restart confirmation screen appears.
5.Press the [Later] button.
⇒The current scanner name, or changed scanner name after next restart, is displayed.
|
| If the scanner name is the same as | |
HINT |
| one already in use, network communi- | |
|
| cation problems will occur. In this | |
|
| case, try the following steps: | |
| 1. | Disconnect the LAN cable, press | |
|
|
| the [Shutdown] button on the |
|
|
| touch panel, and turn the scan- |
|
|
| ner off. |
| 2. | Reboot the scanner with the | |
|
|
| LAN cable disconnected, and |
|
|
| enter a |
|
|
| name. |
| 3. | Reboot the scanner again. | |
| 4. | ||
|
|
| scanner. |
Restart may be performed after all necessary settings have been completed.
Continue with the Region/Timezone settings.
3.4 Setting the Region/Timezone
1.Select the [System Settings] tab on the top menu.
2.Select the [Region/Timezone] tab on the left side menu.
3.Press the [List] button for the "Timezone" input field.
The default timezone is "(GMT+09:00) Osaka, Sapporo, Tokyo".
⇒ A list of timezones appears. 4. Select a timezone.
5. Select whether "Daylight Savings Time" should be on or off.
This option is not shown for timezones where daylight savings time is not used.
6. Press the [OK] button.
⇒The Region/Timezone is set.
Continue with IP address/DHCP settings.
3.5 Setting the IP Address/DHCP
An IP address must be set in order to connect the scanner to a network.
Do not use an IP address that
ATTENTIONalready exists in the network.
IP address duplication will cause an error during setup.
1.Select the [Network Settings] tab on the top menu.
2.Select the [IP Address] tab on the left side menu.
⇒ The IP address/DHCP screen appears.
⇒The "Admin Password" screen appears.
7
⇒The "Region/Timezone" screen appears.
8