Debug Tool and IDE | Fujitsu MB9B500 Series instruction

5 Debug Tool and IDE

FSS MB9BF506R EV-Board supports both Keil U-Link-ME and IAR J-Link for debug shown as following.

Figure 5-1: J-Link Overview

Figure 5-2: U-Link Overview

The U-Link-me should be used with Keil uVision 4 which can be downloaded freely from following web.

https://www.keil.com/update/sw/RVMDK/4.20

The J-Link should be used with IAR Embedded Workbench which can be downloaded freely from following web.

http://www.iar.com/website1/1.0.1.0/68/1/

Page 21

Image 21

Fujitsu MB9B500 Series user manual Debug Tool and IDE, 1 J-Link Overview -2 U-Link Overview

Contents

MB9B500 Series FUJITSU SEMICONDUCTOR SHANGHAI LIMITED32-BIT MICROCONTROLLER APPLICATION NOTE ALL RIGHTS RESERVED Date Revision HistoryVersion 2011-04-21 REVISION HISTORY 2 HARDWARE SETTING1 INTRODUCTION 3 FLASH ON-BOARD PROGRAMMING 1 Introduction 1.1 Product Overview1.2 MB9B506 Series MCU 1.3 Board Features AD channel 2 Hardware Setting 2.4 Setting for USB On-Board Programming 2.3 Setting for UART On-Board Programming2.2 Jumpers Overview Table 2-2 Setting for UART On-Board Programming 2.5 Setting for Debug Tool „ Use IAR J-Link„ Use Keil U-Link ME 3.1 On-Board Programming via UART 3 Flash On-Board Programming Figure 3-7 Press Reset Button 3.2 On-Board Programming via USBFigure 3-4 USB Device Sign Figure 3-5 COM Port in Device Manager Figure 3-8 Start Programming „ Press reset key on the board. Programming will start 4 Sample Code „ Hardware Setting 4.1 UART„ Flowchart „ Usage Figure 4-3 Send UART Data From PC Side 4.3 RTC 4.2 Nand Flash„ Hardware Setting None „ Flowchart Flowchart „ Block Diagram 4.4 CAN 4.5 USB Function 4.6 USB Host 4.7 LCD & AD & Key Figure 5-1 J-Link Overview Figure 5-2 U-Link Overview 5 Debug Tool and IDE „ Run an Existed Project 5.1 Debug with J-Link in IAR EWARM WorkbenchTool bar Project list Log window Watch window Main window 3 Click “Project Rebuild All” 2 Select a project eww fileFigure 5-5 Select a Project Figure 5-6Rebuild All „ Setting for Flash Debug 2 Don’t select “Use macro files” in “DebuggerSetup” table Figure 5-10 Macro File DisabledFigure 5-11 Flash Load File Path 2 Select “Use macro files” in “DebuggerSetup” table „ Setting for RAM DebugFigure 5-13 Macro File Enabled Figure 5-12 ICF File for RAM Debug Figure 5-14 Flash Loader File Disabled „ How to Make a HEX File3 Don’t use Flash loader file 1 Use Flash debug Tool bar Project list Build output 5.2 Debug with U-Link ME in Keil uVision4Figure 5-16 Keil IDE Overview Figure 5-17 Open a Project 3 Rebuild all 2 Select a project uvproj file4 Start debug Figure 5-18 Select a Project Figure 5-21 Debug Tool Bar Figure 5-22 ROM Address Setting for Flash Debug Figure 5-24 Select Update Target Before Debugging 3 Check “Update Target before Debugging” checkbox2 Don’t use initialization file Figure 5-23 Don’t use initialization File 2 Set initialization file path. ..\DebugRAM.ini 1 Set ROM address in Code SRAM area. 0x1fff8000-0x1fffffffFigure 5-25 Set RAM Address for RAM Debug Figure 5-26 Select Initialization File Figure 5-28 HEX File Generation in Keil IDE Figure 5-27 Select Update Target Before Debugging „ Software 6 Materials Download„ Document „ Sample code