„ Setting for Flash Debug | Fujitsu MB9B500 Series manual

5)Use following tool bar to debug

Figure 5-21: Debug Tool Bar

The sample codes support both Flash and RAM debug in Keil uVison 4, if Flash debug is used, the code is programmed into MB9BF506 Flash. If RAM debug is used, the code only runs in RAM area, and after power off, the code will not be stored, but the RAM debug will be faster than Flash debug.

Setting for Flash Debug

1)Set ROM address in Flash area. (0x00000000-0x00080000)

Figure 5-22: ROM Address Setting for Flash Debug

Page 30

Image 30

Fujitsu MB9B500 Series user manual „ Setting for Flash Debug, 21 Debug Tool Bar, 22 ROM Address Setting for Flash Debug

Contents

32-BIT MICROCONTROLLER FUJITSU SEMICONDUCTOR SHANGHAI LIMITEDMB9B500 Series APPLICATION NOTE ALL RIGHTS RESERVED Version Revision HistoryDate 2011-04-21 1 INTRODUCTION 2 HARDWARE SETTINGREVISION HISTORY 3 FLASH ON-BOARD PROGRAMMING 1 Introduction 1.1 Product Overview1.2 MB9B506 Series MCU 1.3 Board Features 2 Hardware Setting AD channel 2.2 Jumpers Overview 2.3 Setting for UART On-Board Programming2.4 Setting for USB On-Board Programming Table 2-2 Setting for UART On-Board Programming 2.5 Setting for Debug Tool „ Use IAR J-Link„ Use Keil U-Link ME 3 Flash On-Board Programming 3.1 On-Board Programming via UART Figure 3-4 USB Device Sign 3.2 On-Board Programming via USBFigure 3-7 Press Reset Button Figure 3-5 COM Port in Device Manager „ Press reset key on the board. Programming will start Figure 3-8 Start Programming 4 Sample Code „ Flowchart 4.1 UART„ Hardware Setting „ Usage Figure 4-3 Send UART Data From PC Side „ Hardware Setting None „ Flowchart 4.2 Nand Flash4.3 RTC Flowchart 4.4 CAN „ Block Diagram 4.5 USB Function 4.6 USB Host 4.7 LCD & AD & Key 5 Debug Tool and IDE Figure 5-1 J-Link Overview Figure 5-2 U-Link Overview Tool bar Project list Log window 5.1 Debug with J-Link in IAR EWARM Workbench„ Run an Existed Project Watch window Main window Figure 5-5 Select a Project 2 Select a project eww file3 Click “Project Rebuild All” Figure 5-6Rebuild All „ Setting for Flash Debug 2 Don’t select “Use macro files” in “DebuggerSetup” table Figure 5-10 Macro File DisabledFigure 5-11 Flash Load File Path Figure 5-13 Macro File Enabled „ Setting for RAM Debug2 Select “Use macro files” in “DebuggerSetup” table Figure 5-12 ICF File for RAM Debug 3 Don’t use Flash loader file „ How to Make a HEX FileFigure 5-14 Flash Loader File Disabled 1 Use Flash debug Figure 5-16 Keil IDE Overview 5.2 Debug with U-Link ME in Keil uVision4Tool bar Project list Build output Figure 5-17 Open a Project 4 Start debug 2 Select a project uvproj file3 Rebuild all Figure 5-18 Select a Project Figure 5-22 ROM Address Setting for Flash Debug Figure 5-21 Debug Tool Bar 2 Don’t use initialization file 3 Check “Update Target before Debugging” checkboxFigure 5-24 Select Update Target Before Debugging Figure 5-23 Don’t use initialization File Figure 5-25 Set RAM Address for RAM Debug 1 Set ROM address in Code SRAM area. 0x1fff8000-0x1fffffff2 Set initialization file path. ..\DebugRAM.ini Figure 5-26 Select Initialization File Figure 5-27 Select Update Target Before Debugging Figure 5-28 HEX File Generation in Keil IDE „ Document 6 Materials Download„ Software „ Sample code

Fujitsu MB9B500 Series user manual Setting for Flash Debug, 21 Debug Tool Bar

Models: MB9B500 Series

Figure 5-21: Debug Tool Bar

Figure 5-22: ROM Address Setting for Flash Debug