Hardware Setting, AD channel | Fujitsu MB9B500 Series specification

2 Hardware Setting

2.1 Main Features
External Power	DB9 Connector	DB9 Connector	LED
External Power	UART channel 0	UART channel 2	LED2-LED4 (P1B-P19)
15V	UART channel 0	UART channel 2	LED2-LED4 (P1B-P19)
15V

JTAG
JTAG		LCD
Connector		LCD
Connector

Potentiome ter

CAN	AD channel 7
CAN
TX0_2, RX0_2

USB Device

USB Host	Nand Flash	RTC	Key	RTC Battery	Key
	attached on external bus	attached on I2C channel 7	“Reset”	”2 pin header”	“Left” (P40), “Right” (P43),
	CS7 area				“Up” (P41), “Down” (P42)

Page 7

Image 7

Fujitsu MB9B500 Series user manual Hardware Setting, AD channel

Contents

APPLICATION NOTE FUJITSU SEMICONDUCTOR SHANGHAI LIMITEDMB9B500 Series 32-BIT MICROCONTROLLER ALL RIGHTS RESERVED 2011-04-21 Revision HistoryDate Version 3 FLASH ON-BOARD PROGRAMMING 2 HARDWARE SETTINGREVISION HISTORY 1 INTRODUCTION 1.1 Product Overview 1 Introduction1.2 MB9B506 Series MCU 1.3 Board Features AD channel 2 Hardware Setting Table 2-2 Setting for UART On-Board Programming 2.3 Setting for UART On-Board Programming2.4 Setting for USB On-Board Programming 2.2 Jumpers Overview „ Use IAR J-Link 2.5 Setting for Debug Tool„ Use Keil U-Link ME 3.1 On-Board Programming via UART 3 Flash On-Board Programming Figure 3-5 COM Port in Device Manager 3.2 On-Board Programming via USBFigure 3-7 Press Reset Button Figure 3-4 USB Device Sign Figure 3-8 Start Programming „ Press reset key on the board. Programming will start 4 Sample Code „ Usage 4.1 UART„ Hardware Setting „ Flowchart Figure 4-3 Send UART Data From PC Side Flowchart 4.2 Nand Flash4.3 RTC „ Hardware Setting None „ Flowchart „ Block Diagram 4.4 CAN 4.5 USB Function 4.6 USB Host 4.7 LCD & AD & Key Figure 5-1 J-Link Overview Figure 5-2 U-Link Overview 5 Debug Tool and IDE Watch window Main window 5.1 Debug with J-Link in IAR EWARM Workbench„ Run an Existed Project Tool bar Project list Log window Figure 5-6Rebuild All 2 Select a project eww file3 Click “Project Rebuild All” Figure 5-5 Select a Project „ Setting for Flash Debug Figure 5-10 Macro File Disabled 2 Don’t select “Use macro files” in “DebuggerSetup” tableFigure 5-11 Flash Load File Path Figure 5-12 ICF File for RAM Debug „ Setting for RAM Debug2 Select “Use macro files” in “DebuggerSetup” table Figure 5-13 Macro File Enabled 1 Use Flash debug „ How to Make a HEX FileFigure 5-14 Flash Loader File Disabled 3 Don’t use Flash loader file Figure 5-17 Open a Project 5.2 Debug with U-Link ME in Keil uVision4Tool bar Project list Build output Figure 5-16 Keil IDE Overview Figure 5-18 Select a Project 2 Select a project uvproj file3 Rebuild all 4 Start debug Figure 5-21 Debug Tool Bar Figure 5-22 ROM Address Setting for Flash Debug Figure 5-23 Don’t use initialization File 3 Check “Update Target before Debugging” checkboxFigure 5-24 Select Update Target Before Debugging 2 Don’t use initialization file Figure 5-26 Select Initialization File 1 Set ROM address in Code SRAM area. 0x1fff8000-0x1fffffff2 Set initialization file path. ..\DebugRAM.ini Figure 5-25 Set RAM Address for RAM Debug Figure 5-28 HEX File Generation in Keil IDE Figure 5-27 Select Update Target Before Debugging „ Sample code 6 Materials Download„ Software „ Document

2 Hardware Setting

AD channel 7