Manuals / Furuno / Marine Equipment / Marine Instruments

Furuno 511, 520, 611 manual 5-10, Alarm messages, their meanings and priorities

Models: 511

1 73

Download 73 pages 24.78 Kb

Page 60

Image 60

5. ALARMS

Alarm messages

The table below shows the alarm messages, their meanings and priorities.

Alarm messages, their meanings and priorities

Message	Meaning	Priority

DEVIATION ALARM	Deviation alarm has occurred.	1

CROSS TRACK ERROR	XTE alarm has occurred.	2

SPEED ALARM	Speed alarm has occurred.	3

DEPTH ALARM	Depth alarm has occurred.	4

WATER TEMP. ALARM	Temperature alarm has occurred.	5

TRIP ALARM	Log alarm has occurred.	6

5-10

Page 60

Image 60

Furuno 511, 520, 611 manual 5-10, Alarm messages, their meanings and priorities

Contents

OPERATORS MANUAL MODEL NAVpilot-511/520/611AUTOPILOT 00014860315 00014860315 Pub. No. OME-72501-F HIMA NAVPILOT-511/520/611A JAN F AUG . 08 The paper used in this manual is elemental chlorine freeSAFETY INSTRUCTIONS Observe the following cautions when using the autopilotDo not use the SIMULATION mode on the boat Do not use the ORBIT mode in rough seaTABLE OF CONTENTS SYSTEM CONFIGURATION1. PRINCIPLE OF THE AUTOPILOT FOREWORD6. MAINTENANCE & TROUBLESHOOTING 5. ALARMSMN-1 SP-1Features FOREWORDA Word to the Owner of the NAVpilot-511/520/611 SYSTEM CONFIGURATION System configuration of NAVpilot-511/520/611Rudder Reference Unit FAP-6111 Remote Controller Distributor FAP-6800 Remote controler Dial type FAP-5551, FAP-5552This page is intentionally left blank 1. PRINCIPLE OF THE AUTOPILOT Principle of AutopilotPrinciple of Operation 1. PRINCIPLE OF THE AUTOPILOT2. BASIC OPERATION Operating ControlsNAVpilot-511/611 NAVpilot-520Turning the power off 2.2 Turning On/OffStartup sequence AUTO PILOT2.3 Adjusting Brilliance and Contrast Main menu ex. STBY modeContrast, brilliance window 2.4.1 Choosing the display mode 2.4 DisplaysDisplays 2.4.2 Selecting the data shown on Data Display Selecting dataSTBY HDG STBY HDGAnalog indicator selection Data available for Normal display 2, Data display and Graphic displayDisplayed data Own ship’s position L/L3.1 STBY Mode STBY mode display Ex. Normal Display3. STEERING MODES STBY3.2 AUTO Mode 3.2.1 Using the AUTO modeAUTO mode display Ex. Normal Display AUTO3.2.2 ADVANCED AUTO mode ADVANCED AUTO mode display Ex. Normal DisplayEnabling the ADVANCED AUTO mode Advanced auto options window3.3 NAV Mode 3.3.1 Starting the NAV modeNAV mode display Ex. Normal Display 359.93.3.2 Selecting sailing method of NAV mode Nav mode options windowNAV mode, COURSE and XTE 3.3.3 Switching waypoint Waypoint switching options windowPage 3.4 TURN Mode Turn menuTURN menu inputting TLL data 180º TURN for AUTO mode only Example of 180º maneuver in turn mode360º TURN for AUTO mode only Example of 360º maneuver in turn modeDo not use the ORBIT mode in rough sea 3-10ORBIT Example of orbit maneuver ex. clockwise3-11 To escape from the ORBIT while it is in use, press STBY keyExample of spiral maneuver in turn mode 3-12SPIRAL 3-13 5. Press the TURN/MENU key once to show the TURN menuExample of FIGURE EIGHT in NAV mode 3-14FIGURE EIGHT Confirm that no objection is in the general vicinity of the waypoint3-15 Navigating to TLL pointTLL navigation ORBIT3.5 REMOTE Mode Dial type remote controller FAP-5551Turning power on dial type FU Follow-Up mode display dial remote controllerTurning power off dial type 3-17Rotating dial 3. When you terminate the REMOTE mode, turn off the remote controllerDodge FAP-6231, 6232 type remote controller Turning power on, button and lever type remote controllersNFU No Follow-Up mode display 3-18Operating remote controller ex. button and lever types Turning power off, button and lever type remote controllers3-19 3.6 DODGE Mode 3.6.1 Dodging in STBY modeDodge mode display 3-203.6.2 Dodging in AUTO or NAV mode DODGE3-21 Dodge mode display3-22 This page is intentionally left blank3. STEERING MODES 4.1 STBY Mode Menu STBY mode menu4. MENU OPERATION MESSAGE4.1.1 Setting parameters Parameter setup menuSelecting the method of entering the parameter Sea state options windowDeviation level options window LEVELSetting parameters manually Example of Manual parameterTrack line and weather setting value Rudder angle and rudder gain settingWEATHER RUDDER GAINfast Boats Speedslow calmAdjusting the sensitivity in monitoring the boat’s trim Auto trim options windowWhen towing the net NAV MODENav mode data source window ex. default setting Auto net towing options windowFISH MODE WAYPOINT SWITCHINGRADIUS OF ORBIT SPIRAL SPEED4.1.2 Setting other menu items System setup menu4-10 Activating key beep4-11 Locking the control unitLock options window Setting the panel dimmer 4-125. ALARMS 5.1 ALARM SETUP MenuAlarm setup menu 5.1.1 Selecting the alarm buzzer Audio alarm options windowAlarm interval options window 5.1.2 Selecting the beep pattern5.1.3 Setting the watch alarm 5.1.4 Setting the heading deviation alarmWatch alarm options window 5.1.5 Setting the cross-track error limit XTE alarm options window5.1.6 Setting the speed alarm Speed alarm options window5.1.7 Setting the depth alarm Depth alarm options window5.1.8 Setting the temperature alarm 5.1.9 Setting the trip distance alarmTemp alarm options window Log trip options window5.1.10 Clearing the trip distance Log trip clear options window5.2 Alarm Information Alarm menuAlarm messages Alarm messages, their meanings and priorities5-10 6. MAINTENANCE & TROUBLESHOOTING 6.1 Preventive MaintenanceMaintenance program Do not open the equipment6.2 Replacement of Fuse 6.3 DiagnosticsUse the proper fuse Parts NamePROCESSOR UNIT TEST CONTROL UNIT TESTHEADING SENSOR TEST 6.MAINTENANCE & TROUBLESHOOTINGKEYBOARD TEST Navpilot-511/611Navpilot-520 SCREEN TESTRUDDER SETUP AND AUTO TEST Rudder test6.4 Clearing Memories SYSTEM DATASystem data screen 6.5 Error Messages Error messagesError message MeaningError messages con’t 6. MAINTENANCE & TROUBLESHOOTINGSTBY mode menu MENU TREEMN-1 MN-2 AUTO mode menuNAV mode menu SPECIFICATIONS OF AUTOPILOT FURUNONAVpilot-511/520/611 CONTROL UNITPOWER SUPPLY ENVIRONMENTAL CONDITIONSUNIT COLOR FURUNOINDEX IN-1