Install USB Drivers | Garmin HN294DP/DI specification

Image 17

Garmin HN294DP/DI manual Install USB Drivers

Contents

User Guide ADSL Wireless RouterHN294dp/di Disclaimer CopyrightAbstract Trademark List Hardware Description and Installation ContentsInitial Configuration Introduction ADSL-mode - RFC1483 Router Advanced ConfigurationADSL-mode - RFC1483 MER Router ADSL-mode - PPPoE Router Important Information Troubleshooting Glossary 1.1 About this User Guide 1.2 About the ADSL Wireless Router HN294d1 Introduction 1.2.1 Ease of Use 1.2.2 Wireless Features 1.2.3 Security 1.2.4 Advanced Possibilities 2.1.1 Package Contents Hardware Description and Installation2.1 Before You Start Figure 1 - HN294d Package Contents 2.2.1 Front Panel and LED Indicators 2.1.2 Subscription for ADSL Service2.2 Physical Appearance Symbol Figure 2 - Back Panel of the HN294d 2.2.2 Back Panel and ConnectorsTable 1 - Description of LEDs Figure 3 - Wall mounting of the HN294d 2.3 Choose a Place for the Router 2.4 Connect the HN294d 2.4.1 Connect Wireless Computers3. Connect the Power Supply 4. Power ON the HN294d 1. Connect the ADSL Line 2.4.2 Connect Computers via Cables2. Connect a client PC to one of the four LAN ports OR to the USB port 2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard 2.5.1 Use DHCP 2.5 Configure Client PCsIn Windows 98/98SE and Me In Windows In Windows XP 2.5.2 Use Static IP Addresses In Windows XP 3.1 Introduction Initial ConfigurationConnection Type Select ADSL-mode 3.2 Access the Configuration Wizard 3.3 Access the Internet 4.1 Description 4 ADSL-mode - RFC1483 Bridge4.2 IP Addresses Assigned by PPPoE RFC1483 2684 Bridged Mode single PVC 4.4 Static IP Addresses 4.3 IP Addresses Assigned by DHCP 5.1 Description 5 ADSL-mode - RFC1483 Router5.2 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC 5.3 Static IP Addresses 6.1 Description 6 ADSL-mode - RFC1483 MER Router 6.2 IP Addresses Assigned by DHCP 7.1 Description 7 ADSL-mode - PPPoE Router 7.3 IP Addresses Assigned by DHCP 7.2 PPPoE Termination and PPPoE Passthrough 8.1 Description 8 ADSL-mode - PPPoA Router 8.2 IP Addresses Assigned by DHCP 9.1 Introduction Advanced Configuration9.2 Access the Web Manager 9.2.1 Outline of the Web Manager 9.3.1 Connect/Disconnect to ISP 9.3 Overview Disconnect 9.4 System 9.4.2 Administration9.4.1 Device Information 9.4.2.1 Account 9.4.2.2 Remote Management 9.4.2.3 Web Port 9.4.3 Backup Configuration 9.4.3.2 Restore 9.4.3.1 Backup 9.4.5 Upgrade Firmware 9.4.4 Save Configuration 9.4.6 Reset Router 9.4.6.1 Reset to Factory Default Parameter 9.5 Status9.5.1 DSL Connection 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.5 DHCP Table 9.5.6 Wireless Client9.5.4 Routing Table EN/LZT 108 6377 R4 - September 9.6.2 LAN Configuration 9.6 Configuration9.6.1 DSL Configuration 9.6.2.1 IP Address Enter your IP settings and click the Apply buttonThe table below describes the parameters 192.168.0.1 and 255.255.255.0 respectively. This 9.6.2.2 DHCP Server Enable and configure the DHCP server Interface Start IP Address End IP Address DHCP lease time Domain Name Servers Enable and configure the DHCP Relay Agent 9.6.3.1 Basic Setup 9.6.3 WLAN Configuration Wireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client Create a new ATM PVC Interface 9.6.4 WAN Configuration selected PPP Configuration IP Configuration 9.6.5.1 Static Route 9.6.5 IP Route Destination Address and Netmask 9.6.5.2 Dynamic Routing 9.6.6.1 DNS Relay 9.6.6 DNS To enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7.1 Firewall 9.6.7 Security EN/LZT 108 6377 R4 - September Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule 9.6.7.2 Intrusion Detection On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.8 Virtual Server Create a new virtual server Internal Host Create a DMZ zoneExternal Packet 9.6.9 IGMP Proxy 9.6.10 UPnP 10.1 Basic Functions 10 TroubleshootingLAN Connection Indication/Symptom 10.2.2 How to use IPCONFIG 10.2.1 How to use WINIPCFG Start Run… type command and click OK . In the 10.3 WAN Connection10.4 WLAN Connection 10.6 Safety Mode 10.5 Reset the HN294d 4. Click the Upgrade button 11 Important Information 11.1 Product Care and Maintenance 11.2 License Agreement 11.2.3 Limited Warranty11.2.1 License 11.2.2 Term 11.2.6 Governing Law 11.2.4 Intended Use11.2.5 Limitation of Liability 11.3 Regulatory Information 11.3.2 Safety Approvals11.3.1 EU Directives 11.3.1.1 Declaration of Conformity 11.3.2.1 UL 1950 Statement 11.3.3 EMC Approvals 11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4 Telecom Approval11.3.3.1 FCC Part 15 Statement 11.3.4.1 FCC Part 68 Statement 11.3.7 Power Supply 11.3.5 Access Point Frequency Band11.3.6 Caution 11.3.8 Environmental Information Access Point GlossaryADSL Asynchronous DHCP Device DOS attack Domain nameDownstream DSLAM Ethernet EncapsulationFirewall Firmware Host G.liteHTTP IEEE MAC address IntranetIP address Ping Peer-to-peerPort POTS SSID RouterSMTP T1.413 Stateful InspectionTCP/IP Telnet Virtual Server UPnPUpstream WLAN VPI and VCI