DSL Configuration, LAN Configuration | Garmin HN294DP/DI specification

Image 52

Garmin HN294DP/DI manual DSL Configuration, LAN Configuration

Contents

HN294dp/di ADSL Wireless RouterUser Guide Copyright DisclaimerAbstract Trademark List Contents Hardware Description and InstallationInitial Configuration Introduction Advanced Configuration ADSL-mode - RFC1483 RouterADSL-mode - RFC1483 MER Router ADSL-mode - PPPoE Router Troubleshooting Important Information Glossary 1 Introduction 1.2 About the ADSL Wireless Router HN294d1.1 About this User Guide 1.2.2 Wireless Features 1.2.1 Ease of Use 1.2.3 Security 1.2.4 Advanced Possibilities Hardware Description and Installation 2.1.1 Package Contents2.1 Before You Start Figure 1 - HN294d Package Contents 2.1.2 Subscription for ADSL Service 2.2.1 Front Panel and LED Indicators2.2 Physical Appearance Symbol Table 1 - Description of LEDs 2.2.2 Back Panel and ConnectorsFigure 2 - Back Panel of the HN294d 2.3 Choose a Place for the Router Figure 3 - Wall mounting of the HN294d 2.4.1 Connect Wireless Computers 2.4 Connect the HN294d3. Connect the Power Supply 4. Power ON the HN294d 2.4.2 Connect Computers via Cables 1. Connect the ADSL Line2. Connect a client PC to one of the four LAN ports OR to the USB port 2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard 2.5 Configure Client PCs 2.5.1 Use DHCPIn Windows 98/98SE and Me In Windows 2.5.2 Use Static IP Addresses In Windows XP In Windows Initial Configuration 3.1 IntroductionConnection Type Select ADSL-mode 3.2 Access the Configuration Wizard 3.3 Access the Internet 4 ADSL-mode - RFC1483 Bridge 4.1 Description4.2 IP Addresses Assigned by PPPoE RFC1483 2684 Bridged Mode single PVC 4.3 IP Addresses Assigned by DHCP 4.4 Static IP Addresses 5 ADSL-mode - RFC1483 Router 5.1 Description5.2 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC 5.3 Static IP Addresses 6 ADSL-mode - RFC1483 MER Router 6.1 Description 6.2 IP Addresses Assigned by DHCP 7 ADSL-mode - PPPoE Router 7.1 Description 7.2 PPPoE Termination and PPPoE Passthrough 7.3 IP Addresses Assigned by DHCP 8 ADSL-mode - PPPoA Router 8.1 Description 8.2 IP Addresses Assigned by DHCP 9.2 Access the Web Manager Advanced Configuration9.1 Introduction 9.2.1 Outline of the Web Manager 9.3 Overview 9.3.1 Connect/Disconnect to ISP Disconnect 9.4.2 Administration 9.4 System9.4.1 Device Information 9.4.2.1 Account 9.4.2.2 Remote Management 9.4.3 Backup Configuration 9.4.2.3 Web Port 9.4.3.1 Backup 9.4.3.2 Restore 9.4.4 Save Configuration 9.4.5 Upgrade Firmware 9.4.6 Reset Router 9.4.6.1 Reset to Factory Default 9.5.1 DSL Connection 9.5 StatusParameter 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.4 Routing Table 9.5.6 Wireless Client9.5.5 DHCP Table Advanced Configuration 9.6.1 DSL Configuration 9.6 Configuration9.6.2 LAN Configuration Enter your IP settings and click the Apply button 9.6.2.1 IP AddressThe table below describes the parameters 192.168.0.1 and 255.255.255.0 respectively. This Enable and configure the DHCP server 9.6.2.2 DHCP Server Interface Start IP Address End IP Address DHCP lease time Enable and configure the DHCP Relay Agent Domain Name Servers 9.6.3 WLAN Configuration 9.6.3.1 Basic Setup Wireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client 9.6.4 WAN Configuration Create a new ATM PVC Interface selected IP Configuration PPP Configuration 9.6.5 IP Route 9.6.5.1 Static Route 9.6.5.2 Dynamic Routing Destination Address and Netmask 9.6.6 DNS 9.6.6.1 DNS Relay To enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7 Security 9.6.7.1 Firewall Advanced Configuration Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.7.2 Intrusion Detection 9.6.8 Virtual Server Create a new virtual server External Packet Create a DMZ zoneInternal Host 9.6.9 IGMP Proxy 9.6.10 UPnP 10 Troubleshooting 10.1 Basic FunctionsLAN Connection Indication/Symptom 10.2.1 How to use WINIPCFG 10.2.2 How to use IPCONFIG 10.4 WLAN Connection 10.3 WAN ConnectionStart Run… type command and click OK . In the 10.5 Reset the HN294d 10.6 Safety Mode 4. Click the Upgrade button 11.1 Product Care and Maintenance 11 Important Information 11.2.3 Limited Warranty 11.2 License Agreement11.2.1 License 11.2.2 Term 11.2.5 Limitation of Liability 11.2.4 Intended Use11.2.6 Governing Law 11.3.2 Safety Approvals 11.3 Regulatory Information11.3.1 EU Directives 11.3.1.1 Declaration of Conformity 11.3.3 EMC Approvals 11.3.2.1 UL 1950 Statement 11.3.3.1 FCC Part 15 Statement 11.3.4 Telecom Approval11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4.1 FCC Part 68 Statement 11.3.5 Access Point Frequency Band 11.3.7 Power Supply11.3.6 Caution 11.3.8 Environmental Information Glossary Access PointADSL Asynchronous Device DHCP Domain name DOS attackDownstream DSLAM Encapsulation EthernetFirewall Firmware G.lite HostHTTP IEEE IP address IntranetMAC address Peer-to-peer PingPort POTS SMTP RouterSSID Stateful Inspection T1.413TCP/IP Telnet Upstream UPnPVirtual Server VPI and VCI WLAN