Important Information | Garmin HN294DP/DI instruction

Image 86

Garmin HN294DP/DI manual Important Information, Product Care and Maintenance

Contents

User Guide ADSL Wireless RouterHN294dp/di Abstract CopyrightDisclaimer Trademark List Initial Configuration ContentsHardware Description and Installation Introduction ADSL-mode - RFC1483 MER Router Advanced ConfigurationADSL-mode - RFC1483 Router ADSL-mode - PPPoE Router Troubleshooting Important Information Glossary 1.1 About this User Guide 1.2 About the ADSL Wireless Router HN294d1 Introduction 1.2.2 Wireless Features 1.2.1 Ease of Use 1.2.3 Security 1.2.4 Advanced Possibilities 2.1 Before You Start Hardware Description and Installation2.1.1 Package Contents Figure 1 - HN294d Package Contents 2.2 Physical Appearance 2.1.2 Subscription for ADSL Service2.2.1 Front Panel and LED Indicators Symbol Figure 2 - Back Panel of the HN294d 2.2.2 Back Panel and ConnectorsTable 1 - Description of LEDs 2.3 Choose a Place for the Router Figure 3 - Wall mounting of the HN294d 3. Connect the Power Supply 2.4.1 Connect Wireless Computers2.4 Connect the HN294d 4. Power ON the HN294d 2. Connect a client PC to one of the four LAN ports 2.4.2 Connect Computers via Cables1. Connect the ADSL Line OR to the USB port 2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard In Windows 98/98SE and Me 2.5 Configure Client PCs2.5.1 Use DHCP In Windows 2.5.2 Use Static IP Addresses In Windows XP In Windows Connection Type Initial Configuration3.1 Introduction Select ADSL-mode 3.2 Access the Configuration Wizard 3.3 Access the Internet 4.2 IP Addresses Assigned by PPPoE 4 ADSL-mode - RFC1483 Bridge4.1 Description RFC1483 2684 Bridged Mode single PVC 4.3 IP Addresses Assigned by DHCP 4.4 Static IP Addresses 5.2 IP Addresses Assigned by DHCP 5 ADSL-mode - RFC1483 Router5.1 Description RFC1483 2684 Routed Mode single PVC 5.3 Static IP Addresses 6 ADSL-mode - RFC1483 MER Router 6.1 Description 6.2 IP Addresses Assigned by DHCP 7 ADSL-mode - PPPoE Router 7.1 Description 7.2 PPPoE Termination and PPPoE Passthrough 7.3 IP Addresses Assigned by DHCP 8 ADSL-mode - PPPoA Router 8.1 Description 8.2 IP Addresses Assigned by DHCP 9.1 Introduction Advanced Configuration9.2 Access the Web Manager 9.2.1 Outline of the Web Manager 9.3 Overview 9.3.1 Connect/Disconnect to ISP Disconnect 9.4.1 Device Information 9.4.2 Administration9.4 System 9.4.2.1 Account 9.4.2.2 Remote Management 9.4.3 Backup Configuration 9.4.2.3 Web Port 9.4.3.1 Backup 9.4.3.2 Restore 9.4.4 Save Configuration 9.4.5 Upgrade Firmware 9.4.6 Reset Router 9.4.6.1 Reset to Factory Default Parameter 9.5 Status9.5.1 DSL Connection 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.5 DHCP Table 9.5.6 Wireless Client9.5.4 Routing Table Advanced Configuration 9.6.2 LAN Configuration 9.6 Configuration9.6.1 DSL Configuration The table below describes the parameters Enter your IP settings and click the Apply button9.6.2.1 IP Address 192.168.0.1 and 255.255.255.0 respectively. This Enable and configure the DHCP server 9.6.2.2 DHCP Server Interface Start IP Address End IP Address DHCP lease time Enable and configure the DHCP Relay Agent Domain Name Servers 9.6.3 WLAN Configuration 9.6.3.1 Basic Setup Wireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client 9.6.4 WAN Configuration Create a new ATM PVC Interface selected IP Configuration PPP Configuration 9.6.5 IP Route 9.6.5.1 Static Route 9.6.5.2 Dynamic Routing Destination Address and Netmask 9.6.6 DNS 9.6.6.1 DNS Relay To enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7 Security 9.6.7.1 Firewall Advanced Configuration Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.7.2 Intrusion Detection 9.6.8 Virtual Server Create a new virtual server Internal Host Create a DMZ zoneExternal Packet 9.6.9 IGMP Proxy 9.6.10 UPnP LAN Connection 10 Troubleshooting10.1 Basic Functions Indication/Symptom 10.2.1 How to use WINIPCFG 10.2.2 How to use IPCONFIG Start Run… type command and click OK . In the 10.3 WAN Connection10.4 WLAN Connection 10.5 Reset the HN294d 10.6 Safety Mode 4. Click the Upgrade button 11.1 Product Care and Maintenance 11 Important Information 11.2.1 License 11.2.3 Limited Warranty11.2 License Agreement 11.2.2 Term 11.2.6 Governing Law 11.2.4 Intended Use11.2.5 Limitation of Liability 11.3.1 EU Directives 11.3.2 Safety Approvals11.3 Regulatory Information 11.3.1.1 Declaration of Conformity 11.3.3 EMC Approvals 11.3.2.1 UL 1950 Statement 11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4 Telecom Approval11.3.3.1 FCC Part 15 Statement 11.3.4.1 FCC Part 68 Statement 11.3.6 Caution 11.3.5 Access Point Frequency Band11.3.7 Power Supply 11.3.8 Environmental Information ADSL GlossaryAccess Point Asynchronous Device DHCP Downstream Domain nameDOS attack DSLAM Firewall EncapsulationEthernet Firmware HTTP G.liteHost IEEE MAC address IntranetIP address Port Peer-to-peerPing POTS SSID RouterSMTP TCP/IP Stateful InspectionT1.413 Telnet Virtual Server UPnPUpstream VPI and VCI WLAN