Intranet, IP address, MAC address | Garmin HN294DP/DI guide

Image 99

Garmin HN294DP/DI manual Intranet, IP address, MAC address

Contents

ADSL Wireless Router HN294dp/diUser Guide Trademark List CopyrightDisclaimer Abstract Introduction ContentsHardware Description and Installation Initial Configuration ADSL-mode - PPPoE Router Advanced ConfigurationADSL-mode - RFC1483 Router ADSL-mode - RFC1483 MER Router Important Information Troubleshooting Glossary 1.2 About the ADSL Wireless Router HN294d 1 Introduction1.1 About this User Guide 1.2.1 Ease of Use 1.2.2 Wireless Features 1.2.3 Security 1.2.4 Advanced Possibilities Figure 1 - HN294d Package Contents Hardware Description and Installation2.1.1 Package Contents 2.1 Before You Start Symbol 2.1.2 Subscription for ADSL Service2.2.1 Front Panel and LED Indicators 2.2 Physical Appearance 2.2.2 Back Panel and Connectors Table 1 - Description of LEDsFigure 2 - Back Panel of the HN294d Figure 3 - Wall mounting of the HN294d 2.3 Choose a Place for the Router 4. Power ON the HN294d 2.4.1 Connect Wireless Computers2.4 Connect the HN294d 3. Connect the Power Supply OR to the USB port 2.4.2 Connect Computers via Cables1. Connect the ADSL Line 2. Connect a client PC to one of the four LAN ports 2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard In Windows 2.5 Configure Client PCs2.5.1 Use DHCP In Windows 98/98SE and Me In Windows XP 2.5.2 Use Static IP Addresses In Windows XP Select ADSL-mode Initial Configuration3.1 Introduction Connection Type 3.2 Access the Configuration Wizard 3.3 Access the Internet RFC1483 2684 Bridged Mode single PVC 4 ADSL-mode - RFC1483 Bridge4.1 Description 4.2 IP Addresses Assigned by PPPoE 4.4 Static IP Addresses 4.3 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC 5 ADSL-mode - RFC1483 Router5.1 Description 5.2 IP Addresses Assigned by DHCP 5.3 Static IP Addresses 6.1 Description 6 ADSL-mode - RFC1483 MER Router 6.2 IP Addresses Assigned by DHCP 7.1 Description 7 ADSL-mode - PPPoE Router 7.3 IP Addresses Assigned by DHCP 7.2 PPPoE Termination and PPPoE Passthrough 8.1 Description 8 ADSL-mode - PPPoA Router 8.2 IP Addresses Assigned by DHCP Advanced Configuration 9.2 Access the Web Manager9.1 Introduction 9.2.1 Outline of the Web Manager 9.3.1 Connect/Disconnect to ISP 9.3 Overview Disconnect 9.4.2.1 Account 9.4.2 Administration9.4 System 9.4.1 Device Information 9.4.2.2 Remote Management 9.4.2.3 Web Port 9.4.3 Backup Configuration 9.4.3.2 Restore 9.4.3.1 Backup 9.4.5 Upgrade Firmware 9.4.4 Save Configuration 9.4.6 Reset Router 9.4.6.1 Reset to Factory Default 9.5 Status 9.5.1 DSL ConnectionParameter 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.6 Wireless Client 9.5.4 Routing Table9.5.5 DHCP Table EN/LZT 108 6377 R4 - September 9.6 Configuration 9.6.1 DSL Configuration9.6.2 LAN Configuration 192.168.0.1 and 255.255.255.0 respectively. This Enter your IP settings and click the Apply button9.6.2.1 IP Address The table below describes the parameters 9.6.2.2 DHCP Server Enable and configure the DHCP server Interface Start IP Address End IP Address DHCP lease time Domain Name Servers Enable and configure the DHCP Relay Agent 9.6.3.1 Basic Setup 9.6.3 WLAN Configuration Wireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client Create a new ATM PVC Interface 9.6.4 WAN Configuration selected PPP Configuration IP Configuration 9.6.5.1 Static Route 9.6.5 IP Route Destination Address and Netmask 9.6.5.2 Dynamic Routing 9.6.6.1 DNS Relay 9.6.6 DNS To enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7.1 Firewall 9.6.7 Security EN/LZT 108 6377 R4 - September Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule 9.6.7.2 Intrusion Detection On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.8 Virtual Server Create a new virtual server Create a DMZ zone External PacketInternal Host 9.6.9 IGMP Proxy 9.6.10 UPnP Indication/Symptom 10 Troubleshooting10.1 Basic Functions LAN Connection 10.2.2 How to use IPCONFIG 10.2.1 How to use WINIPCFG 10.3 WAN Connection 10.4 WLAN ConnectionStart Run… type command and click OK . In the 10.6 Safety Mode 10.5 Reset the HN294d 4. Click the Upgrade button 11 Important Information 11.1 Product Care and Maintenance 11.2.2 Term 11.2.3 Limited Warranty11.2 License Agreement 11.2.1 License 11.2.4 Intended Use 11.2.5 Limitation of Liability11.2.6 Governing Law 11.3.1.1 Declaration of Conformity 11.3.2 Safety Approvals11.3 Regulatory Information 11.3.1 EU Directives 11.3.2.1 UL 1950 Statement 11.3.3 EMC Approvals 11.3.4 Telecom Approval 11.3.3.1 FCC Part 15 Statement11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4.1 FCC Part 68 Statement 11.3.8 Environmental Information 11.3.5 Access Point Frequency Band11.3.7 Power Supply 11.3.6 Caution Asynchronous GlossaryAccess Point ADSL DHCP Device DSLAM Domain nameDOS attack Downstream Firmware EncapsulationEthernet Firewall IEEE G.liteHost HTTP Intranet IP addressMAC address POTS Peer-to-peerPing Port Router SMTPSSID Telnet Stateful InspectionT1.413 TCP/IP UPnP UpstreamVirtual Server WLAN VPI and VCI