Initial Configuration, Introduction | Garmin HN294DP/DI specs

Image 23

Garmin HN294DP/DI manual Initial Configuration, Introduction, Connection Type, Select ADSL-mode

Contents

User Guide ADSL Wireless RouterHN294dp/di Trademark List CopyrightDisclaimer Abstract Introduction ContentsHardware Description and Installation Initial Configuration ADSL-mode - PPPoE Router Advanced ConfigurationADSL-mode - RFC1483 Router ADSL-mode - RFC1483 MER Router Important Information Troubleshooting Glossary 1.1 About this User Guide 1.2 About the ADSL Wireless Router HN294d1 Introduction 1.2.1 Ease of Use 1.2.2 Wireless Features 1.2.3 Security 1.2.4 Advanced Possibilities Figure 1 - HN294d Package Contents Hardware Description and Installation2.1.1 Package Contents 2.1 Before You Start Symbol 2.1.2 Subscription for ADSL Service2.2.1 Front Panel and LED Indicators 2.2 Physical Appearance Figure 2 - Back Panel of the HN294d 2.2.2 Back Panel and ConnectorsTable 1 - Description of LEDs Figure 3 - Wall mounting of the HN294d 2.3 Choose a Place for the Router 4. Power ON the HN294d 2.4.1 Connect Wireless Computers2.4 Connect the HN294d 3. Connect the Power Supply OR to the USB port 2.4.2 Connect Computers via Cables1. Connect the ADSL Line 2. Connect a client PC to one of the four LAN ports 2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard In Windows 2.5 Configure Client PCs2.5.1 Use DHCP In Windows 98/98SE and Me In Windows XP 2.5.2 Use Static IP Addresses In Windows XP Select ADSL-mode Initial Configuration3.1 Introduction Connection Type 3.2 Access the Configuration Wizard 3.3 Access the Internet RFC1483 2684 Bridged Mode single PVC 4 ADSL-mode - RFC1483 Bridge4.1 Description 4.2 IP Addresses Assigned by PPPoE 4.4 Static IP Addresses 4.3 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC 5 ADSL-mode - RFC1483 Router5.1 Description 5.2 IP Addresses Assigned by DHCP 5.3 Static IP Addresses 6.1 Description 6 ADSL-mode - RFC1483 MER Router 6.2 IP Addresses Assigned by DHCP 7.1 Description 7 ADSL-mode - PPPoE Router 7.3 IP Addresses Assigned by DHCP 7.2 PPPoE Termination and PPPoE Passthrough 8.1 Description 8 ADSL-mode - PPPoA Router 8.2 IP Addresses Assigned by DHCP 9.1 Introduction Advanced Configuration9.2 Access the Web Manager 9.2.1 Outline of the Web Manager 9.3.1 Connect/Disconnect to ISP 9.3 Overview Disconnect 9.4.2.1 Account 9.4.2 Administration9.4 System 9.4.1 Device Information 9.4.2.2 Remote Management 9.4.2.3 Web Port 9.4.3 Backup Configuration 9.4.3.2 Restore 9.4.3.1 Backup 9.4.5 Upgrade Firmware 9.4.4 Save Configuration 9.4.6 Reset Router 9.4.6.1 Reset to Factory Default Parameter 9.5 Status9.5.1 DSL Connection 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.5 DHCP Table 9.5.6 Wireless Client9.5.4 Routing Table EN/LZT 108 6377 R4 - September 9.6.2 LAN Configuration 9.6 Configuration9.6.1 DSL Configuration 192.168.0.1 and 255.255.255.0 respectively. This Enter your IP settings and click the Apply button9.6.2.1 IP Address The table below describes the parameters 9.6.2.2 DHCP Server Enable and configure the DHCP server Interface Start IP Address End IP Address DHCP lease time Domain Name Servers Enable and configure the DHCP Relay Agent 9.6.3.1 Basic Setup 9.6.3 WLAN Configuration Wireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client Create a new ATM PVC Interface 9.6.4 WAN Configuration selected PPP Configuration IP Configuration 9.6.5.1 Static Route 9.6.5 IP Route Destination Address and Netmask 9.6.5.2 Dynamic Routing 9.6.6.1 DNS Relay 9.6.6 DNS To enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7.1 Firewall 9.6.7 Security EN/LZT 108 6377 R4 - September Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule 9.6.7.2 Intrusion Detection On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.8 Virtual Server Create a new virtual server Internal Host Create a DMZ zoneExternal Packet 9.6.9 IGMP Proxy 9.6.10 UPnP Indication/Symptom 10 Troubleshooting10.1 Basic Functions LAN Connection 10.2.2 How to use IPCONFIG 10.2.1 How to use WINIPCFG Start Run… type command and click OK . In the 10.3 WAN Connection10.4 WLAN Connection 10.6 Safety Mode 10.5 Reset the HN294d 4. Click the Upgrade button 11 Important Information 11.1 Product Care and Maintenance 11.2.2 Term 11.2.3 Limited Warranty11.2 License Agreement 11.2.1 License 11.2.6 Governing Law 11.2.4 Intended Use11.2.5 Limitation of Liability 11.3.1.1 Declaration of Conformity 11.3.2 Safety Approvals11.3 Regulatory Information 11.3.1 EU Directives 11.3.2.1 UL 1950 Statement 11.3.3 EMC Approvals 11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4 Telecom Approval11.3.3.1 FCC Part 15 Statement 11.3.4.1 FCC Part 68 Statement 11.3.8 Environmental Information 11.3.5 Access Point Frequency Band11.3.7 Power Supply 11.3.6 Caution Asynchronous GlossaryAccess Point ADSL DHCP Device DSLAM Domain nameDOS attack Downstream Firmware EncapsulationEthernet Firewall IEEE G.liteHost HTTP MAC address IntranetIP address POTS Peer-to-peerPing Port SSID RouterSMTP Telnet Stateful InspectionT1.413 TCP/IP Virtual Server UPnPUpstream WLAN VPI and VCI