Gateway CG3000, CG3100 Button Description

Wireless Cable Voice Gateway CG3000/CG3100 User Manual

1-2 Connecting the Gateway

v1.0, July 2009

You can use the LEDs to verify status and connections. The following table lists and describes each LED and button on the front panel of the gateway.

Table 1-1. LED and Front Panel Button Descriptions

LED Description

Power

•Solid green. Power is supplied to the cable modem.

•Off. No power.

Downstream

•Solid green. The unit is synchronized, and all four channels are in use (channel

bonding).

•Blinking. The unit is scanning for a downstream DOCSIS channel.

•Off. No downstream channels are locked.

Upstream

•Solid green. The unit is synchronized, and all four channels are in use (channel

bonding).

•Blinking. The unit is scanning for an upstream channel.

•Off. No upstream channels are locked.

Internet

•Solid green. The cable modem is online.

•Blinking. The cable modem is synchronizing with the cable provider’s CMTS.

•Off. The cable modem is offline.

LAN (Ethernet)

• Green indicates 1,000 Mbps. Amber indicates 10/100 Mbps.

•Solid. An Ethernet device is connected and powered on.

•Blinking. Data is being transmitted or received on the Ethernet port.

•Off. No Ethernet device is detected on the Ethernet port.

Voice P orts

(1 and 2) •Solid green. Registered with the Call Agent.

•Blinking. There is an active call.

•Slow blink. Phone is “on-hook,” registration with Call Agent is in progress.

•Off. No phones are connected to the voice port.

Button Description

Wireless

On/Off

Turn the wireless radio in the gateway on and off. The wireless radio is on by default. The

LED located below this button indicates if the wireless radio is on or off.

Push 'N'

Connect (WPS)

Pushing this button opens a 2-minute window for the gateway to connect with other WPS-

enabled devices. For more information, about using the WPS method to implement secu-

rity, see the Wireless Cable Voice Gateway CG3000/CG3100 User Manual

Contents

Main ii v1.0, July 2009 Trademarks Statement of Conditions FCC Warning Statement Prohibition of Collocation Safety Information Page Page Contents Page Page Page About This Manual Conventions, Formats, and Scope How to Print This Manual Revision History Chapter 1 Connecting the Gateway Package Contents Gateway Front Panel 1-2 Connecting the Gateway Table 1-1. LED and Front Panel Button Descriptions Button Description Gateway Rear Panel Logging In to Your Gateway Page Page Page Chapter 2 Wireless Configuration security setting must be the same for the gateway and wireless computers or wireless adapters. Planning Your Wireless Network certified and WPA or WPA 2 capable, and that they support WPS configuration. Wireless Placement and Range Guidelines Wireless Security Options Manually Configuring Your Wireless Settings and Security Page Wireless Configuration 2-5 Table 2-1. Wireless Settings 2-6 Wireless Configuration Table 2-1. Wireless Settings (continued) Configuring WEP (Wired Equivalent Privacy) Wireless Security Configuring WPA-PSK or WPA2-PSK Wireless Security Using Push 'N' Connect (WPS) to Configure Your Wireless Network and Security Using a WPS Button to Add a WPS Client Page Using a PIN Entry to Add a WPS Client Connecting Additional Wireless Client Devices Adding Just WPS Clients Adding Both WPS and Non-WPS Clients Chapter 3 Content Filtering Viewing or E-mailing Logs Blocking Keywords, Sites, and Services Blocking Keywords and Domains Page Services Port Forwarding Configuring Port Forwarding to Local Servers Adding a Custom Rule Page Page Chapter 4 Managing Your Network Viewing the Modem Status The Modem Status screen fields are explained in the following table. Page Backing Up and Restoring Your Settings Changing the Built-In Password Running Diagnostic Utilities Page Viewing the Event Log Chapter 5 Customizing Your Network DMZ Host LAN IP Setup Page Reserving an IP Address for DHCP Use Configuring Universal Plug and Play (UPnP) NAT Normally the Turn NAT O n check box should be selected, which is the default setting. Chapter 6 Troubleshooting Basic Functions 6-2 Troubleshooting Using LEDs to Troubleshoot The following table provides help when using the LEDs for troubleshooting. Table 6-1. Using LEDs to Troubleshoot Connecting to the Gateways Main Menu Troubleshooting the ISP Connection Troubleshooting a TCP/IP Network Using a Ping Utility Testing the LAN Path to Your Gateway Testing the Path from Your PC to a Remote Device Page Default Settings and Technical Specifications A-1 Appendix A Default Settings and Technical Specifications Factory Default Settings A-2 Default Settings and Technical Specifications Technical Specifications The table below describes the technical specifications for the gateway. Page Page Appendix B Related Documents Page Index Index-2 S T U W