Connect Power Supply, Install junction box cover

Dishwasher Installation

STEP 16: CONNECT POWER SUPPLY

If a power cord with plug is already installed, proceed to Step 17.

If the dishwasher came with a factory-installed power cord and you want to convert it to a permanent connection, refer to the instructions on page 16.

WARNING If house wiring is not 2-wire with a ground wire, a ground must be provided by the installer.

When house wiring is aluminum, be sure to use U.L. listed anti-oxidant compound and aluminum-to-copper connectors.

ADVERTENCIA Si el cableado de la casa no es de 2 cables con un cable de conexión a tierra, el instalador debe suministrar una conexión

a tierra.

Cuando el cableado de la casa es en aluminio, cerciórese de usar un compuesto

anti-oxidante aprobado por U.L. y un compuesto de aluminio a cobre.

•Secure house wiring to the back of the junction box bracket with a strain relief.

•Locate the three dishwasher wires (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box bracket. Use UL-listed wire nuts of appropriate size to connect incoming ground to green, white

to white and black to black.

Figure Z

STEP 17: install junction box cover

If junction box cover is already installed, skip to Step 18.

In this step you will need the junction box cover and the #10 hex-head screw from the screw kit set aside in Step 1.

•Install the junction box cover using the #10 hex- head screw. Check to be sure that wires are not pinched under the cover.

STEP 18: pretest checklist

■Verify that power is turned off at the source.

■Open the dishwasher door and remove all foam and cardboard packaging.

■Read the Owner’s Manual to familiarize yourself with the operation of the dishwasher.

■Check to be sure that the wiring is secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components.

■Check that the door spring does not contact the water line, fill hose, or adjacent cabinets. See Steps 13 and 14.

■Pull lower rack about halfway out. Check to be sure it does not roll back into dishwasher or further out. If it does, relevel the dishwasher. See Step 12.

■Check to be sure control panel does not touch adjacent cabinets. If it does, reposition the dishwasher. See Step 13.

■Turn on the hot water faucet at the sink to verify that the water temperature is at least 120°F and not more than 150°F. Adjust water heater

if necessary .

■Add two quarts of water to the bottom of the dishwasher to lubricate the pump seal.

■Turn on water supply.

■Check for water leaks. Tighten connections

if necessary . See Step 14.

■Remove the protective film, if present, from the control panel, access panel and door panel.

206C1559P195 specifications

The GE 206C1559P195 is a component that belongs to General Electric's suite of high-performance aircraft engine components. Specifically, this part is integral to the Geared Turbofan (GTF) engine technology that GE has pioneered, aiming at increasing fuel efficiency while reducing noise and emissions.

One of the standout features of the GE 206C1559P195 is its advanced aerodynamic design, which plays a crucial role in optimizing the engine's performance. The component helps improve air flow, thereby enhancing thrust and operational efficiency. By utilizing sophisticated Computational Fluid Dynamics (CFD) simulations in its design process, GE has ensured that the part meets the rigorous demands of modern aviation.

The GE 206C1559P195 also incorporates cutting-edge materials technology. Constructed with lightweight yet robust materials, the part significantly contributes to the overall weight reduction of the engine, which is vital for maximizing fuel efficiency. The use of composite materials and advanced alloys ensures that the component can withstand extreme temperatures and pressures associated with high-performance engine operation.

Another characteristic that sets the GE 206C1559P195 apart is its reliability and durability. GE's stringent manufacturing processes and quality control protocols ensure that each component is built to last, reducing maintenance frequency and enhancing operational reliability. The part is designed to have a long service life, making it a cost-effective choice in the long run for airlines and operators.

In terms of technological innovation, the GE 206C1559P195 features integrated sensors that provide real-time data on engine performance. This capability allows for better monitoring and predictive maintenance, thereby increasing safety and reducing unscheduled downtimes.

Furthermore, the integration of digital twin technology enables operators to simulate different operational scenarios, improving decision-making and optimizing maintenance schedules. This technological edge places the GE 206C1559P195 at the forefront of aircraft engine component innovations, aligning with the industry's shift toward sustainability and efficiency.

In summary, the GE 206C1559P195 is a remarkable component that embodies GE's commitment to advance aviation technology, emphasizing performance, durability, and environmental awareness. Its design and technological features reflect the ongoing evolution in the aerospace industry, making it a key asset for modern aircraft engines.

GE 206C1559P195 Connect Power Supply, Install junction box cover, Pretest checklist

Models: 206C1559P195