Safety Instructions

 

 

 

 

 

Operating

Instructions

 

 

 

Care and Cleaning

 

 

 

 

Installation

Instructions

 

 

 

 

 

Troubleshooting

Tips

 

 

 

Consumer Support

 

 

 

 

Before you call for service…

Troubleshooting Tips

Problem

 

Possible Causes

What To Do

 

 

 

 

 

Oven not clean after

 

Oven controls not properly set.

• See the Using the self-cleaning oven section.

a clean cycle

 

 

 

 

 

Oven was heavily soiled.

• Clean up heavy spillovers before starting the clean cycle.

 

 

 

 

 

 

Heavily soiled ovens may need to self-clean again or

 

 

 

 

for a longer period of time.

 

 

 

 

“LOCK DOOR” flashes

 

The self-clean cycle has been

• Close the oven door.

in the display

 

selected but the door is not

 

 

 

closed.

 

 

 

 

 

LOCKED DOOR light

 

The oven door is locked

• Touch the CLEAR/OFF pad. Allow the oven to cool.

is on when you want

 

because the temperature

 

to cook

 

inside the oven has not

 

 

 

dropped below the

 

 

 

locking temperature.

 

 

 

 

 

“F—and a number or

 

You have a function error code.

• Touch the CLEAR/OFF pad. Allow the oven to cool for

letter”flashinthedisplay

 

 

 

one hour. Put the oven back into operation.

 

 

 

 

 

 

 

If the function code repeats.

• Disconnect all power to the range for 5 minutes

 

 

 

 

and then reconnect power. If the function error code

 

 

 

 

repeats, call for service.

 

 

 

 

“Probe” appears in

 

This is reminding you to enter

• Enter a probe temperature.

the display

 

a probe temperature after

 

 

 

plugging in the probe.

 

 

 

 

 

Display goes blank

 

A fuse in your home may be

• Replace the fuse or reset the circuit breaker.

 

 

blown or the circuit breaker

 

 

 

tripped.

 

 

 

 

 

 

 

The clock is in the

• See the Special features of your oven control section.

 

 

black-out mode.

 

 

 

 

 

Display flashes

 

Power failure.

• Reset the clock.

 

 

 

 

Unable to get the

 

Oven control pads were

• The BAKE and BROIL HI/LO pads must be touched at

display to show “SF”

 

not pressed properly.

the same time and held for 3 seconds.

 

 

 

 

Power outage,

 

Power outage or surge.

• Reset the clock. If the oven was in use, you must reset

clock flashes

 

 

 

it by touching the CLEAR/OFF pad, setting the clock

 

 

 

 

and resetting any cooking function.

 

 

 

 

“Burning” or “oily”

 

This is normal in a new oven

• To speed the process, set a self-clean cycle for a

odor emitting from

 

and will disappear in time.

minimum of 3 hours. See the Using the self-cleaning

the vent

 

 

 

oven section.

 

 

 

 

Strong odor

 

An odor from the insulation

• This is temporary.

 

 

around the inside of the oven

 

 

 

is normal for the first few times

 

 

 

the oven is used.

 

 

 

 

 

LOC appears in

 

The Range Lockout feature

• Be sure the surface unit controls are turned OFF.

the display

 

is activated.

Turn this feature off to use the range.

 

 

 

 

See the Range Lockout section.

 

 

 

 

 

46