Manuals / GE / Computer Equipment / Scanner

GE GFK0579B user manual Select the Baud Rate, HHM Display

Models: GFK0579B

1 154

Download 154 pages 8.79 Kb

Page 94

6

Select the Baud Rate

Genius bus communications can occur at any of four baud rates: 153.6 Kbaud standard, 153.6 Kbaud extended, 76.8 Kbaud, or 38.4 Kbaud. The default is 153.6 K baud (standard). The Genius I/O System User's Manual gives guidelines for baud rate selection.

Each device's communications baud rate must be the same as that used by all other devices on the bus, or the bus will not operate.

HHM Display

SELECT BAUD RATE ACTIVE=153.6K ST PROG =153.6K ST tgl entr nxt

Configuration Steps

1.If the baud rate should be changed, press F2 (toggle). When the desired baud rate

appears beside P R O G = , press F3 (enter).

2.If the baud rate is changed on any block that is currently installed on an operating bus, it must be changed on all devices on that bus. After changing the baud rate, you must cycle power at the same time to all devices on the bus to use the new baud rate.

3.Press F4 (nxt) to continue configuring the Remote I/O Scanner.

90	Series 90±70 Remote I/O Scanner User's Manual ± July 1992

Image 94

GE GFK0579B user manual Select the Baud Rate, HHM Display

Contents

GE Fanuc Automation GFL±002 Content of this Manual PrefaceRelated Publications We Welcome Your Comments and SuggestionsContents Chapter Logicmaster 90 Operation with a Remote Drop Chapter Remote I/O Scanner Datagrams 123 Overview Host CPUModule Description BEMConnectors LEDsFor a Series 90±70 PLC Required EquipmentFor a Series FivetPLC Distance Between Racks in a Remote Drop Parts of a Remote DropMultiple Racks Data QuantitiesSeries 90±70 Racks Side ViewSeries 90±70 Power Supplies ModelPowering Two Racks from a Single Power Source Series 90±70 Modules for a Remote Drop Remote Drop CapacityPage Genius Bus Maximum BUS LengthTiming Estimating Bus Scan Time for Remote I/O DropsNumber of Remote Drops on a Bus Maximum Number of Drops per Baud RateHot Standby CPU Redundancy RedundancyCPU Redundancy Duplex CPU RedundancyGenius Bus Redundancy Bus Stubs Connect Other Devices to a Dual BusRedundant Bus Configuations Ïïïï Rïïïïïïï Remote Drop Configuration with a Genius Hand±held Monitor ConfigurationRemote Drop Configuration with Logicmaster 90±70 Configuring a Remote Drop using DatagramsConfigurable Features PCM*, GDS*, ADSConfiguration Protection Preinstallation Check Hardware PackagingSystem Grounding Procedures Rack Installation A42139Rack Grounding Rack Number SelectionDevice Genius BUS Rack Power Supply Switch Power Supply InstallationPower Supplied to Two Racks Module Locations Installing a Module Module Installation and RemovalRemoving a Module Field Wiring to I/O Modules Do not Pull On Door Multiple Racks in a Remote Drop Terminator PlugGenius Bus Connections Single Bus Cable Single Bus TerminationGenius Bus Connections Dual Bus Cables Dual Bus TerminationConnecting a Bus Stub to a Remote I/O Scanner BusStub ConnectionsGrounding Programmer Connection at the Remote I/O ScannerConnection Instructions Serial Port Termination Programmer to Converter Cable Terminating the Remote I/O Scanners Serial Port Multidrop ConnectionsIsolation for the Serial Port Programmer Connections in a Multidrop Network SNP Multidrop with WSI Board in Workmaster SNP Multidrop without WSI Board in Workmaster Series Remote I/O ScannerChapter Remote I/O Scanner Operation Stop/Faulted Mode Run ModeScan Scanner Memory Memory in the Remote I/O ScannerCommunications on the Genius Bus Update RateData Transfer with the Host ThroughputInput Data Sent by the Remote I/O Scanner Input Data MessageOutput Defaults Outputs from the Host to a Remote DropConfiguring Extra References ExampleUsing Option Modules in a Remote Drop Accessing the Host CPU from Option Modules in a Remote DropSending Data from an Option Module to the Host Direct Access to I/O by Option Modules ExampleConfiguration Limits Filenames for Configuration FilesUsing Release 3 Configuration Files with Release 4 Software ªAttachingº Configuration FilesConfiguring a Remote Drop Adding a Remote I/O Scanner to the BusSelecting the Bus Address Drop IDs and Bus Addresses Drop ID Attaching a ªDetachedº FileMap Using Auto I/O Map Map Module Reference AddressesBus Scan Time Impact If some I/O will not be scanned by the central PLCGenius Interface Entries Redund Mode Duplex Def SNP Port EntriesSweep Control Entries Prog Window CommModule Characteristics Configure the Modules in the Remote DropModule Reference Address Return to the Rack Display Entering Additional Modules Completing the Remote Drop Configuration Reference Overlaps Changing Reference Addresses and Lengths Viewing/Editing the I/O MapReference Conflicts in the PLC Configuration Displaying Configured ReferencesViewing PLC References Viewing Remote Drop References Modules Outside the I/O MapUndeleting a Remote Drop Configuration Copying a Remote Drop ConfigurationDeleting a Remote Drop Configuration Copying, Deleting, and UndeletingSelecting an Existing Configuration File Storing the Configuration to the PLC Storing the ConfigurationStoring a Remote Drop Configuration Chapter Logicmaster 90 Operation with a Remote Drop Setting Up Programmer Communications with a Remote Drop Status Display for a Remote Drop Features Not Used for a Remote Drop CPU Configuration Feature DifferencesProgramming Software Differences for a Remote Drop Reference TablesChapter For Additional Information, Also SeeOverview IO 32IN IO 16IN Set Up the Hand±held Monitor Display the Configuration Main Menu F1PROG Block ID F2CONFIG Block F3COPY ConfigRef blk Nxt Select the Device NumberRef nxt HHM Display Series Six/Series Five Host CPU Mode Select a Series Six or Series Five PLC Reference AddressSelect the Baud Rate HHM DisplaySelect Series 90±70 Data Lengths Prog Remote MAP Lengthpts Tgl ref send nxtSelect the Remote Drop ID Return to the Configuration MenuDrop ID Tgl drp send nxt ID#143 R0 S3 32PT 120VAC %Q 1 nxt Display I/O Modules in Remote DropID#143 R0 S2 32PT 120VAC %I 1 nxt ID#143 R0 S4Select BSM Control Select Genius Bus RedundancyTgl entr Nxt Select CPU Redundancy No Cntl Redun tgl entr nxtSelect Configuration Protection FinishingConfigurationChapter Monitoring and Controlling Remote Drop Data Forcing Circuits Toggling I/O Circuits Overriding I/O CircuitsSummary Identifying the Circuit Monitoring/Controlling I/O DataGenius Hand±held Monitor 143#0.2 %IDisplaying Diagnostics for the Circuit Being Monitored Finding the Circuits Series 90 ReferenceMon on off reles Forcing/Unforcing I/OMNTR3 143#0.3 %I 33 STS Ref force diag MNTR3 143#0.3 %I 33 STS Mon on off relesForce to Chng entr MNTR3 143#0.3 %AI 1 STS ±22138 Ref force diagMNTR3 143#0.3 %AI 1 FRC ±22138 Ref force diag MNTR3 143#0.3 %AI 1 STS ±10000 FRC Force releaseDisplaying Other Circuits Logicmaster 90±70 Reference Tables Display from the PLCReference Tables Display for the Remote I/O Scanner Series Six PLC or Series Five PLC Remote Drop Data in I/O Table Memory110 Remote Drop Data in Register Memory Mixed Reference Table DisplaysComputer TablesChapter Diagnostics and Fault Clearing Maximum Number of Uncleared FaultsFault Information on the Block/Bus Status Screen Display and Clear Faults from a Genius Hand±held MonitorBlock V. ACT no FORCE,NO Faul nxt prv actv bus 143#0.2 %I 1 STS Ref force diag Displaying Faults from the Monitor Block ScreensDisplaying Additional Faults DIAG3 143#0.3 #IFault Table Display with a Rev Bus Controller Display and Clear Faults from Logicmaster 90±70Fault Table at the PLC Fault ClearingFault Table at the Remote I/O Scanner Fault T a B L EPLC Fault Table at the Series 90±70 PLC Slot 1 is occupied by the Remote I/O ScannerPLC Fault Table at the Remote I/O Scanner Status References Reference Nickname DefinitionDisplay and Clear Faults from Logicmaster 5 or Logicmaster Fault ClearingChapter Remote I/O Scanner Datagrams For Additional Information, Also SeeDatagram Types Read Map Reply Read MapWrite Map Report Fault Datagram Format Fault ByteFault Bytes 4 Fault Bytes 6Appendix Estimating the Number of Remote Drops for a Bus 131 Series 90±70 Remote I/O Scanner Uses Manual ± July PLC Configuration Steps AppendixCreate or Select a PLC Program Folder Add the Remote I/O Scanner to the Genius BusPage 136 Configure the Remote I/O Scanner Entering the Scanners Remote Drop IDAssigning I/O References for the Remote I/O Scanner Input Default/Out Enable Using the Copy Configuration Feature Store the Configuration to the PLCUsing Reference View from the PLC Program Folder 141 Remote Drop Configuration Summary Create a Folder \LM90\central\Replace displayed module? Y/N Entering the Remote Drops I/O Configuration Series Six or Series Five PLC Reference Entering Communications and Operating ParametersDefinitions of Communications and Operating Parameters Crete±only remote dropsConfiguring I/O Module Options Configuring Reference AddressesConfiguration Limits Reference View from a Remote DropStore the Configuration to the Remote Drop Index 152 153 154