GE LTC MAP, LTC-MAP 2130 Section 2: Getting Started

70055MP Revision D February 3, 2000

Section 2: Getting Started

Receiving Inspection

On receipt of the LTC-MAP 2130 Monitor:

1. Carefully inspect the packing containers and contents for physical

damage.

2. Carefully unpack the monitor, checking that all items listed on the

packing slip are present and in good condition.

NOTE: If damage is evident, or any items are missing, contact

Support Services at (330-425-3755) for further instructions.

Customer Support/Service

For service or support for your LTC-MAP 2130 Monitor, contact:

Field Service/Customer Support Department

Reuter-Stokes, Inc.

Edison Park

8499 Darrow Rd.

Twinsburg, OH 44087

PH: 330-425-3755

FAX: 330-425-1812

GE Syprotec

179 Boulevard Brunswick

Pointe-Claire, Quebec H9R 5N2

Canada

PH: 514-694-3637

FAX: 514-694-9245

www.gepower.com

Contents

Main LTC-MAP 2130 Monitor Product Manual LTC-MAP 2130 Monitor Copyright Information Trademarks Warranty Revision History Table of Contents Section 1: Introduction Section 2: Getting Started Section 3: Installation Page Section 1: Introduction Product Overview Page Section 1: Introduction 1-3 70055MP Revision D February 3, 2000 Specifications Input 1-4 Section 1: Introduction February 3, 2000 70055MP Revision D General Section 1: Introduction 1-5 70055MP Revision D February 3, 2000 Electrical Environmental NOTE: Specifications subject to change without notice. Physical Enclosure Available Options Table 1-1: LTC-MAP 2130 Options Typical Application Page Manual Conventions Section 2: Getting Started Receiving Inspection Customer Support/Service Front Cover Layout Face Panel Layout Operating Conditions Button Alarm Status & Settings Button Acknowledge Alarm Button LCD Display < < Serial Port Circuit Board Location Section 2: Getting Started 2-7 70055MP Revision D February 3, 2000 I/O Board Figure 2-5: I/O Circuit Board POWER #2 #1 Page Page Communications Section 3: Installation Selecting a Location Mounting the Monitor Cable Installation 3-4 Section 3: Installation February 3, 2000 70055MP Revision D I/O Board Configuration Jumpers POWER 9V JP10 JP14 6V Modem Power Supply Configuration Jumper Table 3-2: Modem Power Supply Configuration (JP12) Alarm Configuration Jumpers Ground Jumpers Wiring Overview 3-8 Section 3: Installation GND #2 #1 HEATER Page Wiring the Sensors Wiring a Tap Position Indicator OEM Potentiometers 0 to +5 VDC or 0 to +10 VDC Power -5 to +5 VDC or -10 to +10 VDC Power LTC-MAP Power Page After-Market Wiring the AC Voltage Inputs Wiring the AC Current Inputs Wiring the Digital Inputs Wiring the Annunciator Outputs Wiring the Internal Heater Wiring Power Establishing Communications Serial Port Communications Modem Communications Initial Start Up Calibrate Tap Position Section 4: Operation Overview Operating Conditions Button Analog Channel Readings Screens Digital Channel Readings Screens Tap Change Summary Screen Alarm Status & Settings Button LTC-MAP Status Screen Current Time and Date Screen Acknowledging Alarms 70055MP Revision D February 3, 2000 Section 5: Troubleshooting Procedures Refer to Table 5-1 for common troubleshooting procedures. Table 5-1: Common Troubleshooting Procedures Page 70055MP Revision D February 3, 2000 Appendix A: User-Specific Information Forms Analog Channel Configuration Page Page Page Page Appendix B: Firmware Upgrades Page Page Appendix C: Glossary of Terms Index A B C F G H I L S T V W GE Energy Management . I S