GE LTC MAP, LTC-MAP 2130 Alarm Configuration Jumpers , Ground Jumpers

3-6 Section 3: Installation

February 3, 2000 70055MP Revision D

Alarm Configuration Jumpers

Jumpers JP18 and JP19 set the annunciator relay outputs to normal or

inverted. Jumper JP13 configures the Acknowledge Alarm button. Refer to

Table 3-3 for jumper positions. Refer to Figure 3-3 for jumper locations.

NOTE: JP13 must always be installed.

Table 3-3: Alarm Configuration

Jumper Position Description

JP18 INV

NORM

Annunciator 1 Output Inverted.

Annunciator 1 Output Normal.

JP19 INV

NORM

Annunciator 2 Output Inverted.

Annunciator 2 Output Normal.

JP13 Installed

Removed

Configures the Alarm Acknowledge button for use.

Not applicable.

Ground Jumpers

Jumpers JP10 and JP14, when installed, are set to earth ground. These

jumpers must always be installed for accurate and safe operation.

WARNING: Jumpers JP10 and JP14 must always be installed for accurate

and safe monitor operation.

Contents

Main LTC-MAP 2130 Monitor Product Manual LTC-MAP 2130 Monitor Copyright Information Trademarks Warranty Revision History Table of Contents Section 1: Introduction Section 2: Getting Started Section 3: Installation Page Section 1: Introduction Product Overview Page Section 1: Introduction 1-3 70055MP Revision D February 3, 2000 Specifications Input 1-4 Section 1: Introduction February 3, 2000 70055MP Revision D General Section 1: Introduction 1-5 70055MP Revision D February 3, 2000 Electrical Environmental NOTE: Specifications subject to change without notice. Physical Enclosure Available Options Table 1-1: LTC-MAP 2130 Options Typical Application Page Manual Conventions Section 2: Getting Started Receiving Inspection Customer Support/Service Front Cover Layout Face Panel Layout Operating Conditions Button Alarm Status & Settings Button Acknowledge Alarm Button LCD Display < < Serial Port Circuit Board Location Section 2: Getting Started 2-7 70055MP Revision D February 3, 2000 I/O Board Figure 2-5: I/O Circuit Board POWER #2 #1 Page Page Communications Section 3: Installation Selecting a Location Mounting the Monitor Cable Installation 3-4 Section 3: Installation February 3, 2000 70055MP Revision D I/O Board Configuration Jumpers POWER 9V JP10 JP14 6V Modem Power Supply Configuration Jumper Table 3-2: Modem Power Supply Configuration (JP12) Alarm Configuration Jumpers Ground Jumpers Wiring Overview 3-8 Section 3: Installation GND #2 #1 HEATER Page Wiring the Sensors Wiring a Tap Position Indicator OEM Potentiometers 0 to +5 VDC or 0 to +10 VDC Power -5 to +5 VDC or -10 to +10 VDC Power LTC-MAP Power Page After-Market Wiring the AC Voltage Inputs Wiring the AC Current Inputs Wiring the Digital Inputs Wiring the Annunciator Outputs Wiring the Internal Heater Wiring Power Establishing Communications Serial Port Communications Modem Communications Initial Start Up Calibrate Tap Position Section 4: Operation Overview Operating Conditions Button Analog Channel Readings Screens Digital Channel Readings Screens Tap Change Summary Screen Alarm Status & Settings Button LTC-MAP Status Screen Current Time and Date Screen Acknowledging Alarms 70055MP Revision D February 3, 2000 Section 5: Troubleshooting Procedures Refer to Table 5-1 for common troubleshooting procedures. Table 5-1: Common Troubleshooting Procedures Page 70055MP Revision D February 3, 2000 Appendix A: User-Specific Information Forms Analog Channel Configuration Page Page Page Page Appendix B: Firmware Upgrades Page Page Appendix C: Glossary of Terms Index A B C F G H I L S T V W GE Energy Management . I S