Safety Instructions
Operating Instructions
Troubleshooting Tips
Consumer Support
About the dishwasher control panel.
4 Enhancements (continued)
| ADDED HEAT | When selected, the cycle will run longer with heating elements on to improve both wash and dry |
(EXTRA HOT WASH) | performance. | |
|
| NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
| PRE WASH | For use with heavily soiled and/or |
| (on some models) | starting the cycle. This option adds 16 minutes to the cycle time. |
|
| NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
| HEATED DRY | Shuts off the drying heat option. Dishes will air dry naturally (PDW8900 Series) or |
| Light Off | fan dry (PDW9700 and PDW9900 Series) to save energy. |
|
|
|
| HEATED DRY | PDW8900 Series: Turns the heater on for fast drying. This will extend the total cycle |
| Light On | time by 8 minutes for the SPEED CYCLE and 30 minutes for all other cycles. |
|
| PDW9700 and PDW9900 Series: Turns the heater on for fast drying. This will extend the total |
|
| cycle time by 30 minutes for the |
|
| COOKWARE cycle, 8 minutes for the SPEED cycle, 15 minutes for the PLASTICS cycle and 30 |
|
| minutes for all other cycles. |
|
| NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
| LOCK | You can lock the controls to prevent any selections from being made. Or you can lock the controls |
|
| after you have started a cycle. |
|
| Children cannot accidentally start dishwasher by touching pads with this option selected. |
|
| To unlock the dishwasher controls, press and hold the HEATED DRY pad for 3 seconds. To lock the |
|
| dishwasher, press and hold the HEATED DRY pad for 3 seconds. The light above the LOCK pad |
|
| will turn off. |
| RESET | To change a cycle after washing starts… |
|
| PDW8900 Series: Touch the START/RESET pad to cancel the cycle. The START/RESET light will |
|
| flash while the water is pumped out if needed. This takes approximately 105 seconds. |
|
| PDW9700 and PDW9900 Series: Open the door slowly to prevent |
|
| START/RESET pad to cancel the cycle. If the START/RESET light is flashing, close the door |
|
| until the water pumps out (this takes approximately 105 seconds) and the light stops flashing. |
|
| When the light stops flashing, the dishwasher can be reprogrammed and restarted. |
5 Start
PDW8900 Series
Close the dishwasher door and select the cycle and desired enhancements. Touch the START/RESET pad to begin the cycle. Water fill begins immediately, and approximately 60 seconds later the wash action begins.
When the dishwasher door is fully closed, the control panel lights will display the last settings you selected. If you don’t want to change any of the settings, simply touch the START/RESET pad to begin the cycle.
If the door is closed, the indicator lights will turn off if the START/RESET pad is not selected within 5 minutes. To activate the display, open and close the door or press any pad.
PDW9700 and PDW9900 Series
After selecting the cycle and desired enhancements, touch the START/RESET pad to ready the dishwasher to begin the cycle. Close the door to start the cycle or begin the DELAY START countdown. When the cycle starts, the water fill begins and approximately 60 seconds later the wash action begins.
The dishwasher will always display your last selection and enhancements. If you don’t want to change the settings, simply touch the START/RESET pad to ready the dishwasher and close the door to begin the cycle.
Also, if a power failure occurs NORMAL and HEATED DRY will automatically be programmed. Make any new selections and touch the START/RESET pad to begin the new cycle.
If the door is opened, the indicator lights will turn off if the START/RESET pad is not selected within 5 minutes. To activate the display, open and close the door or touch any pad.
6
