PSB2200N
GE Profile Advantium® 240 Wall Oven
Preparation with an Accessory Drawer
Prepare the opening
The Advantium 240V can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation.
Single Advantium 240V Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown.
* For existing cutouts, a
|
|
|
| ||
maximum width of | 30” |
| |||
|
|
|
|
| |
is acceptable. If the opening |
|
|
|
|
|
is slightly wider, secure a |
|
|
|
|
|
|
|
|
| ||
furring strip on each side of |
|
|
|
| |
|
|
| Min. |
| |
the cutout for securing the |
|
|
|
|
|
oven. |
|
|
|
|
|
| 21” |
Prepare the opening (cont.)
When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium 240V and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides.
•the support must be level and rigidly mounted, flush with the bottom edge of the cutout.
Installation over a GE/Monogram Oven and Warming Drawer:
|
|
| Construct Solid |
| 30” | Bottom Min. | |
|
|
| 3/8” Plywood |
|
|
| Supported by |
|
|
| 2x4 or 2x2 |
|
| Runners all | |
|
| Four Sides | |
|
| Min. |
|
|
| 21” | 2” Min. |
|
|
| (3” recommended |
|
|
| Per Oven |
|
|
| Requirement |
5” min. |
|
|
|
from floor |
|
| 2” Min. |
1” min. |
|
| |
|
|
| |
above | Per warming drawer requirement | ||
toekick |
|
|
|
• Always maintain |
|
| Construct | |
|
| |||
|
| |||
minimum height from |
|
| Base | |
the floor to the cutout in |
|
| Min. 3/8” | |
5” min. | Plywood | |||
any single or combined | from floor | Supported | ||
by 2x4 or 2 | ||||
1” min. | ||||
installation. | Runners all | |||
above | Four Sides | |||
• Allow 3/4" to | toekick |
| ||
|
|
| ||
trim overlap on the sides |
|
|
| |
and 7/8" overlap on the |
|
|
| |
bottom of the opening for |
|
|
| |
all models. The amount of overlap on the sides depends on the | ||||
actual cutout width. Allow |
models PSB2200 and PSB2201 and for models ZSC2200, ZSC2201 and ZSC2202.
30”
21”
5” min. from floor 1” min. above toekick
Construct | ||||||
|
| Solid Bottom | ||||
|
| Min. 3/8” | ||||
|
| Plywood | ||||
|
| Supported | ||||
| by 2x4 or 2x2 | |||||
Min. |
| Runners all | ||||
|
| Four Sides | ||||
|
|
|
|
|
|
|
|
|
| 2” Min. | |||
|
|
| (3” recommended |
| ||
|
|
|
|
|
|
|
|
|
|
| Per warming |
| |
|
|
|
| drawer |
| |
|
|
|
| requirement |
| |
|
|
|
|
|
|
|
*For existing cutouts, a maximum width of
Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
Caution: For personal safety, the mounting surface must be capable of supporting the
• Oven overlaps will conceal cut edges on all sides of the opening.
For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.
*For existing cutouts, a maximum width of
wider, secure a furring strip on each side of the cutout for securing the oven.
Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
cabinet load, in addition to the added weight of this approximate
Listed by
Underwriters
Laboratories
Specification Created 9/08 | 240442 |