GE ZET2, ZET1 installation instructions Cabinetry, A6 Cutout for Frameless Cabinets

Cabinetry

A4	Single Oven Cutout		A5
	for Installation Over
	a Monogram Warming
	Drawer	23 1/2”
		(59.7 cm)

Min.

Inside

Double Oven Cutout for Installation Over a Monogram Warming

Drawer 23 1/2”

(59.7 cm) Min. Inside

275/16”

(69.2 cm) Max.

9” (22.9 cm)

Max.

91/4”

(23.5 cm).

281/2”

(72.4 cm).

2” x 2” (5 cm x 5 cm) or 2” x 4” (5 cm x 10 cm)

Anti-Tip Block Against Rear Wall, 9” (22.9 cm)

From Floor to Bottom of Block

2” (5.1 cm)	NOTE: Install the
Min.
Allow 5/8”	oven only with
	specific models
(1.5 cm)
	listed on the label
Overlap
	located on top of
on All
	the oven.
Sides

		2” x 2” (5 cm x
		5 cm) or 2” x
		4” (5 cm x 10
		cm) Anti-Tip
		Block Against
		Rear Wall, 9”
		(22.9 cm)
51 15/16”		From Floor
		to Bottom
(131.8 cm)
		of Block
Max.
		2” (5.1 cm)
		Min.
9” (22.9 cm)
	9 1/4”	Allow 5/8”
Max.
	(23.5 cm).	(1.5 cm)
		Overlap
		on All
	28 1/2”	Sides
	(72.4 cm)

1” (2.5 cm) Min. Above Toekick or

Adjust to Oven Installation Height

1” (2.5 cm) Min. Above Toekick

NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior 23 1/2” (59.7 cm) depth and 9 1/4” (23.5 cm) height.

•These Monogram Ovens require 3/4” (1.9 cm) overlap on both sides. Allow 1” (2.5 cm) Min. for top overlap and clearance to upper doors.

•The Monogram Warming Drawers require 5/8” (1.6 cm) overlap on all sides.

•When installing a Monogram Warming Drawer below a single or double oven, a separate 120V, 60 Hz, properly grounded receptacle must be installed. Refer to installation instructions packed with the Warming Drawer for specific installation requirements.

A6 Cutout for Frameless Cabinets

Frameless Cabinets

Whenever possible, order 30” (76.2 cm) frameless cabinet with the cutout sided to fit the oven. If using stock cabinets, additional finished filler pieces may be required to cover the opening.

•A stock frameless cabinet cutout width may be up to 28 3/4” (73 cm). If necessary, add 1/2” (1.3 cm) cleats to the sides, flush with the front edge of the side panels to accept mounting screws.

					30”
			(76.2			cm)
Install 1/2”
(1.3 cm)
Cleats to
Hold Oven
Mounting
		28		1/2	” (72.4 cm)
Screws
					Min.
		28		5/8	” (72.7 cm)
Double					Max.
51 15/16”	(131.8 cm)
Single
27 5/16”	(69.2 cm)

Cabinet Depth

231/2” (59.7 cm)

Min. From Inside Back to Front of Cabinet Frame or Side Panel

3/4” (1.9 cm) Min.

Thick Bottom Shelf Cut Back Flush with Front of Side Panel

8