INSTALLATION INSTRUCTIONS

Right end view

Back view

3/4″ 237/8″

177/8″

1/4″ O.D. water line compression fitting at water valve

Water inlet solenoid valve

3413/32″

4″ long 5/8″ I.D. rubber drain tube—run to open drain

71/2″

33/4″

71/2″

11/4″ Min.

Bend field supplied water line to Figure 1 connect to water valve fitting

 

 

 

 

 

 

 

 

 

 

 

 

9″

 

 

 

 

21/2″

 

 

 

 

 

 

 

 

 

 

 

 

 

Hole for field

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/4″

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supplied water line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90°

90°

341/2″ 9″

 

Max.

 

41/2″ to

 

center line

 

18″

Figure 2

 

UTILITIES

OBSERVE LOCAL CODES

Each installation is unique but will require:

•A cold water inlet of 1/4″ O.D. soft copper tubing and a shutoff valve.

•Either a gravity drain system or a sump pump to lift the water to an existing drain.

•An electrical branch circuit of 115 volt, 60 Hz.

1 phase, with a 15 amp delayed action fuse or circuit breaker.

FOR THE PLUMBER

Connect to water. (Observe local codes.)

•Use 1/4″ O.D. soft copper tubing for the cold water supply.

•Provide a convenient manual shutoff valve in the water line.

•Position the tubing so it can enter the access hole located in the right-hand rear of the icemaker cabinet. The tubing should extend beyond the cabinet front so when the icemaker is pushed back in position it will reach the water inlet location in the front. See Figure 1.

NOTE: Always purge the water line before making the final connection to the inlet of the water valve to prevent possible water valve malfunction.

With the icemaker in its permanent location, bend the tubing to meet the connection at the water valve. The garden hose threaded compression fitting is found in the parts bag. This joint provides a convenient disconnect for service. Be sure the tubing is clear of compressor, to prevent rattle.

LEVELING

•After placing the icemaker into position, check to make certain the icemaker is level side to side and front to back.

•Accurate leveling is essential for proper operation.

•The icemaker should be shimmed so that it is solid as well as level. The shims should be of hard permanent type material such as masonite.

•Compliance with National Sanitation Foundation standards requires that this type of product be sealed to the floor at the bottom rail in order to prevent contamination from spills or the entrance of vermin. Therefore, we recommend that when installing the icemaker you seal it to the floor in accordance with those standards. A silicone-type sealer is recommended.

ALTERNATE METHOD

If a drain connection directly below the drain tube outlet is not available, install a UL-listed drain pump in the rear compartment of the icemaker.

Drain pump specifications:

•UL-listed and have a UL-listed, 120VAC, 3-wire grounded service cord

•Overall outside dimensions (maximum):

15″ wide x 6″ deep x 91/2″ high

•Pump flow rate (minimum): 24.0 gph (0.4 gpm) @ 12 feet lift

•Operating temperature range 55°F. to 110°F. (13°C. to 43°C.)

(continued next page)

17

Page 16 Page 18
Page 17
Image 17
GE Monogram ZDIB50 Each installation is unique but will require, An electrical branch circuit of 115 volt, 60 Hz
Page 16 Page 18

ZDIB50 specifications

The GE Monogram ZDIB50 is a standout built-in refrigerator that offers a fusion of sophisticated design and advanced technology, appealing to culinary enthusiasts and design aficionados alike. With a total capacity of 20.7 cubic feet, this refrigerator provides ample storage space for groceries, beverages, and other essentials, making it a perfect fit for any modern kitchen.

One of the standout features of the ZDIB50 is its dual-compressor system, which allows for independent temperature control of the refrigerator and freezer compartments. This technology not only maintains optimal temperatures but also ensures food preservation by minimizing temperature fluctuations. The refrigerator’s advanced climate control system includes humidity-controlled crispers, which help keep fruits and vegetables fresh for longer periods, enhancing the overall longevity of your food items.

The design of the GE Monogram ZDIB50 is as impressive as its features. Its sleek stainless steel exterior, complemented by integrated handles, adds a touch of elegance to any kitchen. The unit also comes with a customizable panel option, allowing homeowners to match it with their cabinetry for a seamless look. Inside, the refrigerator features glass shelves that are adjustable and spill-proof, making clean-up and organization a breeze. The bright LED lighting illuminates the interior, showcasing the contents and making it easier to find what you need.

In terms of energy efficiency, the ZDIB50 boasts significant energy savings, being ENERGY STAR certified. This certification not only benefits the environment but also helps reduce utility costs for homeowners. The refrigerator is equipped with smart features that allow users to monitor and manage its performance remotely through a smartphone app, giving added convenience to busy lifestyles.

The ice maker is another highlight of the GE Monogram ZDIB50, producing a plentiful supply of crescent-shaped ice, which is perfect for entertaining guests or enjoying refreshing beverages. The water filtration system ensures that the ice is made from clean and purified water, enhancing safety and flavor.

In conclusion, the GE Monogram ZDIB50 combines cutting-edge technology, excellent efficiency, and sophisticated design into one remarkable appliance. It reflects the perfect balance of style and functionality, catering to those who demand the best in their kitchen. Whether you are a casual cook or a gourmet chef, this refrigerator is sure to enhance your culinary experience.
Top Page Image Contents