Gigabyte GA-K8NF-9 specification

English

Temp Limit of Low Speed (Default temperature: 20oC)

The CPU fan will stop spinning when the CPU temperature is below the value set in Temp of FAN turn off option. The CPU fan will start to spin again with the parameter set in CPU FAN: Low Speed when the CPU temperature exceeds the value set in Temp Limit of Low Speed.

Temp Limit of Mid Speed (Default temperature: 50oC)

When the CPU temperature exceeds the value set in this option, the CPU fan spins with the parameter specified in CPU FAN: Mid Speed. For example, by default, when the CPU temperature exceeds 50oC, CPU fan runs with parameter 12.

Temp Limit of High Speed (Default temperature: 60oC)

When the CPU temperature exceeds the value set in this option, the CPU fan rotates with the parameter specified in CPU FAN: High Speed. For example, by default, when the CPU temperature exceeds 60oC, CPU fan runs with parameter 80.

Temp of full FAN Speed (Default temperature: 70oC)

When the CPU temperature exceeds the value set in this option, the CPU fan runs at full speed.

GA-K8NF-9(rev. 2.2) Motherboard

- 42 -

Image 42

Gigabyte GA-K8NF-9 Temp Limit of Low Speed Default temperature 20oC, Temp Limit of Mid Speed Default temperature 50oC

Contents

GA-K8NF-9rev Motherboard Copyright Product Manual Classification Table of Contents Drivers Installation GA-K8NF-9rev .2 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your Computer Feature Summary LAN 4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPU Installation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In Connector USB1 / FUSB2 / FUSB3 Front USB Connector 14 F11394 / F21394 Front Ieee 1394 Connectors Clrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main Menu Main Menu For example Bios Ver. D1 F12 For Boot Menu „ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI Configuration Time IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Init Display First On-Chip IDE Channel0 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel1 On-Chip MAC Lan controlled by Vitesse 8201 phy On-Chip LAN Boot ROMIDE Prefetch Mode NV IDE/SATA RAID function Onboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard Parallel Port Power Management Setup KB Power on Password Power On by MousePower On by Keyboard AC Back Function PnP/PCI Configurations Current VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPM CPU FAN Fail Warning CPU Warning TemperatureTemp of FAN turn off Default temperature 0oC CPU Smart FAN Control Note Temp Limit of High Speed Default temperature 60oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp of full FAN Speed Default temperature 70oC K8 CPU Clock Ratio HT Frequency RatioCPU Frequency Current DDR speed Chipset core PCI-E voltage HT-Link voltage controlDDR voltage control Top Performance Set Supervisor/User Password Save & Exit Setup Exit Without Saving English Drivers Installation Install Chipset Drivers Software Application Software Information Hardware Information Contact Us English Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utility Using the Q-FlashTMutility Steps You can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility bar Congratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and steps English Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system Disabled NV Sata 1 Secondary Appendix Step Save and exit Bios Setup GA-K8NF-9rev .2 Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver Disk Installing Sata controller driver during OS installation NForce Storage Controller Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows Solutions YES English Introduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting AMI Bios Beep Codes English English English Contact Us Taiwan Headquarters China Shanghai