Goodman Mfg ASPF Air Handlers, IO-431 Aspf Wiring Diagram, G W1 W2 Y1 Y2 O DH 1 2 3 4

HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING. WARNING MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

ASPF Wiring Diagram

FL

TL

HTR1

	BK	BK	1
		RD	2
BK	PU		3
	BL
	M1		4
	R		5
	M2
	WH		6
	BK		7
	BK
	RD		8

FL
HTR1	TL
FL
HTR2	TL
	BK

		RD	BK	1
			RD	2
RD		PU		3
		BL
BK	M1	M3		4
	R			5
	M2	M4
		WH		6
	BK
	RD			7
	BK
		RD		8

	FL
		HTR1		TL
	FL
				TL
		HTR2
				RD
		HTR3		TL
					BK	1
		RD		YL		2
					PU
	YL
		BK
				BL		3
		M1	M3	M1	RD
					BL	4
RD
		M2	M4	M2
			R1	R2	BR	5
BK	BK
		RD			WH	6
						7
			YL			8
				BK
			RD			9

FL				TL
	HTR1
FL
				TL
	HTR2
	HTR3			TL
	HTR4			TL
				BL
					BK	1
			PU			2
BL	BK RD
				BL		3
YL	M1	M3	M5	M7	RD
					BL	4
RD	M2	M4	M6	M8
BK		R1		R2	BR	5
BK	RD				WH	6
						7
		YL	BL			8
			BK
		RD				9

9

9

L1 L2

L1 L2

L1 L2 L1 L2

L1 L2 L1 L2

ONE (1) ELEMENT ROWS

TWO (2) ELEMENT ROWS

THREE (3) ELEMENT ROWS

FOUR (4) ELEMENT ROWS

NOTE: WHEN INSTALLING HEATER KIT, ENSURE SPEED TAP DOES NOT EXCEED MINIMUM BLOWER SPEED (MBS) SPECIFIED FOR THE AIRHANDLER/HEATER

KIT COMBINATION ON THIS UNIT'S S&R PLATE. AFTER INSTALLING OPTIONAL HEAT KIT, MARK A "X" IN THE PROVIDED ABOVE. MARK ACCORDING TO NUMBER OF HEATER ELEMENT ROWS INST ALLED. NO MARK INDICATES NO HEAT KIT INSTALLED.

SEE NOTE 2		GRD				EQUIPMENT GROUND
						USE COPPER WIRE
R C G W1 W2 Y1 Y2 O DH 1 2 3 4 5	L1	L2
PLM	1	2	3	4	5	6	7	8	9
RD
PLF	1	2	3	4	5	6	7	8	9
GR	BK	RD		BL	BR	WH	SEE
BR							NOTE 4

208/240 VOLTS

L1

1PLM

1 PLF		EM
		L GN
1		SEE NOTE 1
	2	3

TR

L2

PLM 2

PLF 2

5

WH
BL
RD
WH
			PU
CR					BK			RD
		4		SEE	BK				SEE
			WH	NOTE 3					NOTE 1
RD	2	5		RD	C	1	2	3	240
									TR
GR	1	3				5	24V	4
			BL						BL
							BL
		BL							FUSE	WH PU
					BL
RD					RD				HOLDER	OR BR YL
										1 2 3 4 5
COPPER POWER SUPPLY										EM
(USE RATING PLATE)										C L G N
USE MIN. 75° C FIELD WIRE									RD BK BL

IF REPLACEMENT OF THE ORIGINAL WIRES

SUPPLIED WITH THIS ASSEMBLY IS NECESSARY,

USE WIRE THAT CONFORMS TO THE NATIONAL

ELECTRIC CODE.

		3	1	2	4
FUSE HOLDER	4 24V	5			CR
	6	5 4 PLF			1
					2	EM
					3
					4	C
					5
	R C G W1 W2 Y1 Y2 O DH 1 2 3 4 5

	COLOR CODE			WIRING CODE
BK	BLACK	GR	GREEN	FACTORY WIRING
RD	RED	PU	PURPLE	HIGH VOLTAGE
YL	YELLOW	BR	BROWN	LOW VOLTAGE
BL	BLUE	WH	WHITE	FIELD WIRING
				HIGH VOLTAGE
COMPONENT CODE				LOW VOLTAGE
				TR	TRANSFORMER
EM	EVAPORATOR MOTOR
TB	TERMINAL BOARD			PLF	FEMALE PLUG CONNECTOR
R	RELAY			PLM	MALE PLUG CONNECTOR
CR	CONTROL RELAY			FL	FUSE LINK
EBTDR	ELECTRONIC BLOWER TIME			TL	THERMAL LIMIT
NOTES:	DELAY RELAY			HTR	HEAT ELEMENTS
1) RED WIRES TO BE ON TRANSFORMER TERMINAL "3" FOR 240 VOLTS AND ON TERMINAL
"2" FOR 280 VOLTS.
2) SEE COMPLETE WIRING DIAGRAMS IN INSTALLATION INSTRUCTIONS FOR PROPER LOW
VOLTAGE WIRING CONNECTIONS.
3) CONFIRM SPEED TAP SELECTION IS APPROPRIATE FOR APPLICATION. IF SPEED TAP
NEEDS TO BE CHANGED, CONNECT PURPLE WIRE FROM TERMINAL 4 OF CR RELAY TO
APPROPRIATE TAP AT TB						0140A00040-D
4) BROWN AND WHITE WIRES ARE USED FOR HEAT KITS ONLY.

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

13