Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 309410 manual Digital Tracking Systemt DTS Operation, Do Startup steps 1, Main Menu

Models: 309410

1 24

Download 24 pages 53.96 Kb

Page 12

Image 12

Digital Tracking Systemt (DTS)

Operation

Close cover when spraying to protect from overspray

Main Menu

1. Do Startup steps 1. – 3.

PAINT

FLUSH

2. Start engine or motor, page 9.

Sprayer Model momentarily displays, e. g., C5900 = GMax 5900 Convertible

Pressure display appears. Dashes appear when pressure is less than 200 psi (14 bar, 1.4 MPa).

Note: Information other than pressure can not be accessed if system pressure is greater than 200 psi (14 bar, 1.4 MPa). or if the pump switch is ON.

12309410

Page 12

Image 12

Graco Inc 309410 manual Digital Tracking Systemt DTS Operation, Do Startup steps 1, Start engine or motor, page, Main Menu

Contents

S Controls S Setup S Startup S Cleanup S Pressure Relief S Error Codes309410 Rev. B 233709à la pression maximale de service du système ADVERTÊNCIAMISE EN GARDE ADVERTENCIATrigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatillo Contractor309410 CONTROLS / CONTROLES / COMMANDES / CONTROLESSetup 1. Disconnect engine power cord 2. Release tension bar4. Install motor drop in and push forward Change Engine to Motor7. Plug in pressure control power cord 6. Secure motor with tension barEngage Setup2. Connect other end of hose to gun 3. Tighten securely 4. Remove tip guardSetup 5. Install clean inlet strainer 6. Fill throat packing nut with TSL to prevent premature packing wearDo this each time you spray and store cold 8. Fill fuel tank 9. Ground sprayer with grounding clamp3. Set pump switch OFF Startup2. Turn prime valve down Turn pressure control to lowest pressure PAINT FLUSHc. Set throttle to fast d. Set engine switch ON e. Pull starter cord g. Set throttle to desired settinga b c d e f g 4. Start engine a. Move fuel valve to open b. Move choke to closedDo not stop leaks with your hand or a rag! If StartupSwitchTip and Guard Assembly 1. Engage trigger safety2. Insert SwitchTipt Insert seat and OneSealt seat SwitchTipDigital Tracking Systemt DTS Operation 1. Do Startup steps 12. Start engine or motor, page Main MenuDigital Tracking System DTS Volume WatchDogt Pump Protection SystemTo Activate 1. Do Startup Change Display Units Pressure3. Simultaneously press DTS button and set pump on/off switch on Resettable Hour Meter appears1. Do Startup steps 1. - 3. Pressure must be at zero 2. Start engine or motor, page 9. Pressure display appears4. Press and hold to reset to zero, or 12. Turn pump switch OFF at any time to exit stored data mode 9. Short press DTS button again to move to WatchDog MAN manual mode11. Short press to return to step Secondary Menu - Stored Data and WatchDog Pump Protection ModesSpray Test Pattern Clearing Tip ClogsCleanup 1. Set pump switch OFF. Turn engine or motor OFF2. Turn pressure to lowest setting. Trigger gun to relieve pressure 3. Turn prime valve down 4. Remove guard and SwitchTip6. Clean filter, guard and SwitchTip in flushing fluid 8. Turn engine ON and start engine or motor. Set pump switch ON 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF DTS Error Codes Service309410 309409Graco Warranty ADDITIONAL WARRANTY COVERAGEGraco Phone Number FOR GRACO CANADA CUSTOMERS