Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 309410 manual

Models: 309410

1 24

Download 24 pages 53.96 Kb

Page 22

Image 22

13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF.

PAINTFLUSH

Caution: If flushing with water, do not leave water in sprayer. Flush again with mineral spirits, oil or Pump Armor and leave this protective coating in the sprayer to help prevent freezing or corrosion and increase sprayer life.

14. Make sure plastic center tube is tightened securely. Install filter bowl and filter. Hand tighten filter bowl. Hand tighten gun han- dle.

15. Wipe sprayer, hose and gun with a rag soaked in water or mineral spirits.

16. Clean tip, guard and gasket with a soft bristle brush to prevent part failure due to dried materials. Assemble parts and attach loosely onto gun.

FLUSH

22309410

Page 22

Image 22

Contents

309410 Rev. B S Controls S Setup S StartupS Cleanup S Pressure Relief S Error Codes 233709MISE EN GARDE à la pression maximale de service du systèmeADVERTÊNCIA ADVERTENCIA309410 Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatilloContractor CONTROLS / CONTROLES / COMMANDES / CONTROLES4. Install motor drop in and push forward Setup1. Disconnect engine power cord 2. Release tension bar Change Engine to MotorEngage 7. Plug in pressure control power cord6. Secure motor with tension bar Setup4. Remove tip guard 2. Connect other end of hose to gun 3. Tighten securelySetup Do this each time you spray and store 5. Install clean inlet strainer6. Fill throat packing nut with TSL to prevent premature packing wear cold 8. Fill fuel tank 9. Ground sprayer with grounding clamp2. Turn prime valve down Turn pressure control to lowest pressure 3. Set pump switch OFFStartup PAINT FLUSHa b c d e f g c. Set throttle to fast d. Set engine switch ON e. Pull starter cordg. Set throttle to desired setting 4. Start engine a. Move fuel valve to open b. Move choke to closedDo not stop leaks with your hand or a rag! If Startup2. Insert SwitchTipt Insert seat and OneSealt SwitchTip and Guard Assembly1. Engage trigger safety seat SwitchTip2. Start engine or motor, page Digital Tracking Systemt DTS Operation1. Do Startup steps 1 Main MenuDigital Tracking System DTS To Activate 1. Do Startup VolumeWatchDogt Pump Protection System Change Display Units Pressure1. Do Startup steps 1. - 3. Pressure must be at zero 3. Simultaneously press DTS button and set pump on/off switch onResettable Hour Meter appears 2. Start engine or motor, page 9. Pressure display appears4. Press and hold to reset to zero, or 11. Short press to return to step 12. Turn pump switch OFF at any time to exit stored data mode9. Short press DTS button again to move to WatchDog MAN manual mode Secondary Menu - Stored Data and WatchDog Pump Protection ModesSpray Test Pattern Clearing Tip Clogs2. Turn pressure to lowest setting. Trigger gun to relieve pressure Cleanup1. Set pump switch OFF. Turn engine or motor OFF 3. Turn prime valve down 4. Remove guard and SwitchTip6. Clean filter, guard and SwitchTip in flushing fluid 8. Turn engine ON and start engine or motor. Set pump switch ON 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF 309410 DTS Error CodesService 309409Graco Phone Number Graco WarrantyADDITIONAL WARRANTY COVERAGE FOR GRACO CANADA CUSTOMERS