Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 309410 manual Digital Tracking System DTS

Models: 309410

1 24

Download 24 pages 53.96 Kb

Page 13

Image 13

Digital Tracking System (DTS)

3.Short press DTS button to move to Job Gallons (or Liters x 10).

Note: JOB displays briefly, then the number of gallons sprayed above 1000 psi (70 bar, 7 MPa).

4.Press and hold to reset to zero, or short press DTS button to move to Lifetime Gallons (or Liters x 10).

Note: LIFE displays briefly, then the number of gallons sprayed above 1000 psi (70 bar, 7 MPa).

5.Short press DTS button to move to Auto- Clean Timer operation (Manual 309278).

Note: If the pump is started in the timer mode, the timer counts down to zero and shuts the pump OFF. Use for flushing only.

6. Short press DTS button to return to Pressure.

309410 13

Page 13

Image 13

Graco Inc 309410 manual Digital Tracking System DTS

Contents

S Cleanup S Pressure Relief S Error Codes S Controls S Setup S Startup309410 Rev. B 233709ADVERTÊNCIA à la pression maximale de service du systèmeMISE EN GARDE ADVERTENCIAContractor Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatillo309410 CONTROLS / CONTROLES / COMMANDES / CONTROLES1. Disconnect engine power cord 2. Release tension bar Setup4. Install motor drop in and push forward Change Engine to Motor6. Secure motor with tension bar 7. Plug in pressure control power cordEngage Setup4. Remove tip guard 2. Connect other end of hose to gun 3. Tighten securelySetup 6. Fill throat packing nut with TSL to prevent premature packing wear 5. Install clean inlet strainerDo this each time you spray and store cold 8. Fill fuel tank 9. Ground sprayer with grounding clampStartup 3. Set pump switch OFF2. Turn prime valve down Turn pressure control to lowest pressure PAINT FLUSHg. Set throttle to desired setting c. Set throttle to fast d. Set engine switch ON e. Pull starter corda b c d e f g 4. Start engine a. Move fuel valve to open b. Move choke to closedStartup Do not stop leaks with your hand or a rag! If1. Engage trigger safety SwitchTip and Guard Assembly2. Insert SwitchTipt Insert seat and OneSealt seat SwitchTip1. Do Startup steps 1 Digital Tracking Systemt DTS Operation2. Start engine or motor, page Main MenuDigital Tracking System DTS WatchDogt Pump Protection System VolumeTo Activate 1. Do Startup Change Display Units PressureResettable Hour Meter appears 3. Simultaneously press DTS button and set pump on/off switch on1. Do Startup steps 1. - 3. Pressure must be at zero 2. Start engine or motor, page 9. Pressure display appears4. Press and hold to reset to zero, or 9. Short press DTS button again to move to WatchDog MAN manual mode 12. Turn pump switch OFF at any time to exit stored data mode11. Short press to return to step Secondary Menu - Stored Data and WatchDog Pump Protection ModesClearing Tip Clogs Spray Test Pattern1. Set pump switch OFF. Turn engine or motor OFF Cleanup2. Turn pressure to lowest setting. Trigger gun to relieve pressure 3. Turn prime valve down 4. Remove guard and SwitchTip6. Clean filter, guard and SwitchTip in flushing fluid 8. Turn engine ON and start engine or motor. Set pump switch ON 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF Service DTS Error Codes309410 309409ADDITIONAL WARRANTY COVERAGE Graco WarrantyGraco Phone Number FOR GRACO CANADA CUSTOMERS