Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 309410 manual Do not stop leaks with your hand or a rag! If, Startup

Models: 309410

1 24

Download 24 pages 53.96 Kb

Page 10

Image 10

Do not stop leaks with your hand or a rag! If

Startup

5.Set pump switch ON.

– Pump/clutch is now active –

15 SEC

6.Increase pressure enough to start pump stroking and allow fluid to circulate for 15 seconds; turn pressure down, turn prime valve horizontal.

7. Take spray gun trigger safety OFF.

safety OFF

ti2870a

8.Hold gun against grounded metal flushing pail. Trigger gun and increase fluid pressure slowly until pump runs smoothly.

FLUSH
Note: Inspect fittings for leaks.	Do not stop leaks with your hand or a rag! If

leaks occur, turn sprayer OFF immediately. Do Pressure Relief in Cleanup, 1. – 3. on page 19. Tighten leaky fittings. Repeat Startup, 1. – 5. If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6.

10309410

Page 10

Image 10

Graco Inc 309410 manual Do not stop leaks with your hand or a rag! If, Startup

Contents

309410 Rev. B S Controls S Setup S StartupS Cleanup S Pressure Relief S Error Codes 233709MISE EN GARDE à la pression maximale de service du systèmeADVERTÊNCIA ADVERTENCIA309410 Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatilloContractor CONTROLS / CONTROLES / COMMANDES / CONTROLES4. Install motor drop in and push forward Setup1. Disconnect engine power cord 2. Release tension bar Change Engine to MotorEngage 7. Plug in pressure control power cord6. Secure motor with tension bar Setup4. Remove tip guard 2. Connect other end of hose to gun 3. Tighten securelySetup Do this each time you spray and store 5. Install clean inlet strainer6. Fill throat packing nut with TSL to prevent premature packing wear cold 8. Fill fuel tank 9. Ground sprayer with grounding clamp2. Turn prime valve down Turn pressure control to lowest pressure 3. Set pump switch OFFStartup PAINT FLUSHa b c d e f g c. Set throttle to fast d. Set engine switch ON e. Pull starter cordg. Set throttle to desired setting 4. Start engine a. Move fuel valve to open b. Move choke to closedDo not stop leaks with your hand or a rag! If Startup2. Insert SwitchTipt Insert seat and OneSealt SwitchTip and Guard Assembly1. Engage trigger safety seat SwitchTip2. Start engine or motor, page Digital Tracking Systemt DTS Operation1. Do Startup steps 1 Main MenuDigital Tracking System DTS To Activate 1. Do Startup VolumeWatchDogt Pump Protection System Change Display Units Pressure1. Do Startup steps 1. - 3. Pressure must be at zero 3. Simultaneously press DTS button and set pump on/off switch onResettable Hour Meter appears 2. Start engine or motor, page 9. Pressure display appears4. Press and hold to reset to zero, or 11. Short press to return to step 12. Turn pump switch OFF at any time to exit stored data mode9. Short press DTS button again to move to WatchDog MAN manual mode Secondary Menu - Stored Data and WatchDog Pump Protection ModesSpray Test Pattern Clearing Tip Clogs2. Turn pressure to lowest setting. Trigger gun to relieve pressure Cleanup1. Set pump switch OFF. Turn engine or motor OFF 3. Turn prime valve down 4. Remove guard and SwitchTip6. Clean filter, guard and SwitchTip in flushing fluid 8. Turn engine ON and start engine or motor. Set pump switch ON 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF 309410 DTS Error CodesService 309409Graco Phone Number Graco WarrantyADDITIONAL WARRANTY COVERAGE FOR GRACO CANADA CUSTOMERS