Admin

 

Administrator password. Only administrator can configure the “Advanced

 

 

Password

 

Settings” page. Password field is purposely left blank for security reason

 

 

 

 

after clicking update and saved. The maximum password length is 25

 

 

 

 

characters.

 

 

 

 

 

 

 

 

 

 

 

 

Silence

 

This controls the silence suppression/VAD feature of G723 and G729. If set

 

 

Suppression

 

to “Yes”, when a silence is detected, small quantity of VAD packets (instead

 

 

 

 

of audio packets) will be sent during the period of no talking. If set to “No”,

 

 

 

 

this feature is disabled.

 

 

 

 

 

 

 

 

 

 

 

 

Voice Frames

 

This field contains the number of voice frames to be transmitted in a single

 

 

per TX

 

packet. When setting this value, the user should be aware of the requested

 

 

 

 

packet time (used in SDP message) as a result of configuring this parameter.

 

 

 

 

This parameter is associated with the first vocoder in the above vocoder

 

 

 

 

Preference List or the actual used payload type negotiated between the 2

 

 

 

 

conversation parties at run time.

 

 

 

 

e.g., if the first vocoder is configured as G723 and the “Voice Frames per

 

 

 

 

TX” is set to be 2, then the “ptime” value in the SDP message of an INVITE

 

 

 

 

request will be 60ms because each G723 voice frame contains 30ms of

 

 

 

 

audio. Similarly, if this field is set to be 2 and if the first vocoder chosen is

 

 

 

 

G729 or G711 or G726, then the “ptime” value in the SDP message of an

 

 

 

 

INVITE request will be 20ms.

 

 

 

 

If the configured voice frames per TX exceeds the maximum allowed value,

 

 

 

 

the BudgeTone 200 will use and save the maximum allowed value for the

 

 

 

 

corresponding first vocoder choice. The maximum value for PCM is

 

 

 

 

10(x10ms) frames; for G726, it is 20 (x10ms) frames; for G723, it is 32

 

 

 

 

(x30ms) frames; for G729/G728, 64 (x10ms) and 64 (x2.5ms) frames

 

 

 

 

respectively.

 

 

 

 

 

 

 

 

 

 

 

 

Layer 3 QoS

 

This field defines the layer 3 QoS parameter which can be the value used for

 

 

 

 

IP Precedence or Diff-Serv or MPLS. Default value is 48.

 

 

 

 

 

 

 

 

 

 

 

 

Layer 2 QoS

 

This contains the value used for layer 2 VLAN tag. Default setting is

 

 

 

 

blank.

 

 

 

 

 

 

 

 

 

 

 

 

No Key Entry

 

Default is 4 seconds.

 

 

Timeout

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use # as

 

This parameter allows users to configure the “#” key to be used as the

 

 

Send Key

 

“Send” (or “Dial”) key. If set to “Yes”, pressing this key will immediately

 

 

 

 

trigger the sending of dialed string collected so far. In this case, this key is

 

 

 

 

essentially equivalent to the “(Re)Dial” key. If set to “No”, this “#” key will

 

 

 

 

then be included as part of the dial string to be sent out.

 

 

 

 

 

 

33

Page 33
Image 33
Grandstream Networks 200 Admin, Silence, Suppression, Voice Frames, Per TX, Layer 3 QoS, Layer 2 QoS, No Key Entry