Table 15: Advanced Settings
|
|
|
|
|
|
| Admin |
| Administrator password. Only the administrator can access the “Advanced Settings” and |
| |
| Password |
| “Account Settings” page. Password field is purposely blank for security reasons after |
| |
|
|
| clicking update and saved. The maximum password length is 25 characters. |
| |
|
|
|
|
|
|
|
|
|
|
| |
| G723 rate |
| Encoding rate for G723 codec. By default, 6.3kbps rate is set. |
| |
|
|
|
|
|
|
|
|
|
|
| |
| iLBC frame size |
| iLBC packet frame size. Default is 20ms. For Asterisk PBX, 30ms might be required. |
| |
|
|
|
|
|
|
|
|
|
|
| |
| iLBC payload |
| Payload type for iLBC. Default value is 97. The valid range is between 96 and 127. |
| |
| type |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Silence |
| This controls the silence suppression/VAD feature of the audio codec G.723 and G.729. |
| |
| Suppression |
| If set to “Yes”, when silence is detected, a small quantity of VAD packets (instead of |
| |
|
|
| audio packets) will be sent during the period of no talking. If set to “No”, this feature is |
| |
|
|
| disabled. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Voice Frames |
| This field contains the number of voice frames to be transmitted in a single Ethernet |
| |
| per TX |
| packet (be advised the IS limit is based on the maximum size of Ethernet packet is 1500 |
| |
|
|
| byte (or 120kbps)). |
|
|
|
|
| When setting this value, be aware of the requested packet time (ptime, used in SDP |
| |
|
|
| message) is a result of configuring this parameter. This parameter is associated with the |
| |
|
|
| first codec in the above codec Preference List or the actual used payload type |
| |
|
|
| negotiated between the 2 conversation parties at run time. e.g., if the first codec is |
| |
|
|
| configured as G.723 and the “Voice Frames per TX” is set to 2, then the “ptime” value in |
| |
|
|
| the SDP message of an INVITE request will be 60ms because each G.723 voice frame |
| |
|
|
| contains 30ms of audio. Similarly, if this field is set to 2 and the first codec is G.729 or |
| |
|
|
| G.711 or G.726, then the “ptime” value in the SDP message of an INVITE request will be |
| |
|
|
| 20ms. |
|
|
|
|
| If the configured voice frames per TX exceeds the maximum allowed value, the IP phone |
| |
|
|
| will use and save the maximum allowed value for the corresponding first codec choice. |
| |
|
|
| The maximum value for PCM is 10 (x10ms) frames; for G.726, it is 20 (x10ms) frames; |
| |
|
|
| for G.723, it is 32 (x30ms) frames; for G.729/G.728, 64 (x10ms) and 64 (x2.5ms) frames |
| |
|
|
| respectively. |
|
|
|
|
| Please be careful when editing these parameters. Adjusting these parameters will also |
| |
|
|
| change the dynamic jitter buffer. The GXP has a patent dynamic jitter buffer handling |
| |
|
|
| algorithm. The jitter buffer range is 20 ~ 200 ms. |
| |
|
|
| Grandstream recommends using the default settings provided. Grandstream does not |
| |
|
|
| recommend adjusting these parameters if you are an average user. Incorrect settings |
| |
|
|
| will affect the voice quality. | Please refer to the Codec FAQ at |
|
|
|
| http://www.grandstream.com/faqscodec.html for more technical detail. |
| |
|
|
|
|
|
|
|
|
|
|
| |
| Layer 3 QoS |
| This field defines the layer 3 QoS parameter. It is the value used for IP Precedence or |
| |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
| Layer 2 QoS |
| This contains the value used for layer 2 VLAN tag. Default setting is blank. |
| |
|
|
|
|
|
|
|
|
|
|
|
|
| No Key Entry |
| Default is 4 seconds. |
|
|
| Timeout |
|
|
|
|
|
|
|
|
|
|
Grandstream Networks, Inc. | GXP User Manual | Page 28 of 38 |
| Firmware 1.1.5.15 | Last Updated: 12/2007 |
