CARE AND CLEANING

Cleaning and sanitizing frequency must be followed according to state and local health department regulations.

NOTE: Each time the freezer is fully disassembled, all foodzone freezer components must be thoroughly washed and sanitized using procedures recommended by the local health department. In lieu of local health department recommendations, use a three compartment sink; one compartment to wash parts in detergent, one compartment to rinse, and one to sanitize.

Drain and Rinse

1.If the freezer is empty, proceed to Disassembly and Cleaning. If there is product in the freezer, turn either the right or left front panel switch to “CLEAN”. Most users schedule cleaning when product in the hopper is low to minimize product loss.

2.On freezers using the optional Remote Fill Control and Proportioning Pump, turn “OFF” the water valve on the Proportioning Pump, using the valve next to the inlet pressure regulator and turn the switch on the Remote Fill Control to “OFF”.

3.Open the front dispensing valve and drain all product from the freezer. Close the dispensing valve and turn freezer to “OFF”.

NOTE: Use approximately 2½ gallons (10 liters) of cool water to rinse product out of freezer.

4.Remove the carburetor tube and pour water into the storage hopper. Allow the water to fill the freezing cylinder.

5.Turn the panel switch to “CLEAN” for 5 minutes.

6.Open the dispensing valve and drain the water from the freezer.

7.Turn the freezer “OFF”.

Disassembly and Cleaning

Note: For cleaning and sanitizing before initial start-up remove carb tubes, dispense plungers, handles and springs from parts bag first.

1.Disassemble the dispensing valve assembly (Figure M). Pull out valve handle retaining pin while supporting the valve plunger from the bottom (Figure N). Push up on the valve plunger and remove the stainless handle (Figure O). Slide the valve plunger and spring downward to remove (Figure P).

2.Remove knobs and carefully remove the front dispensing valve assembly, leaving the dasher assembly in the cylinder. Remove the o-rings from the plunger assembly and back of the dispensing valve body. (See Figure Q)

Figure M Disassemble

Figure N Remove Pin Figure O Remove Handle

Figure P Remove

Dispensing Valve

 

Plunger and Spring

NOTE: The best way to remove an o-ring is to first wipe off all of the lubricant using a clean paper towel. Pinch the o-ring upward with a dry paper towel between your index finger and thumb. When a loop is formed in the o-ring, roll it out of the groove with your other thumb. Always remove the o-ring farthest from the

end of the plunger first. Carefully inspect the o-rings and replace if necessary. (See Figure Q)

3.Remove the dasher assembly from inside the freezing cylinder taking care to avoid damaging the rear seal assembly at the back of the freezing cylinder. Disassemble the dasher assembly by removing the stator rod and front and rear stator rod bearings.

Figure Q Ring Removal

Page 8

Model 3312

 

 

Page 10
Image 10
Grindmaster 3311 manual Care and Cleaning, Drain and Rinse, Disassembly and Cleaning

3311 specifications

The Grindmaster 3311 is a highly regarded coffee grinder designed specifically for commercial use, particularly popular among coffee shops and cafes for its reliability and efficiency. Its robust construction ensures longevity, making it a preferred choice for businesses that require consistent performance to meet high customer demand.

One of the main features of the Grindmaster 3311 is its powerful grinding mechanism. It utilizes high-quality burrs that deliver a uniform grind size, which is essential for brewing an exceptional cup of coffee. This grinder is designed to handle a wide variety of coffee beans, allowing establishments to explore diverse coffee offerings without compromising on quality.

Another standout characteristic of the Grindmaster 3311 is its intuitive user interface. The grinder typically integrates a digital display, which aids in easy operation and allows users to select grind sizes with precision. This level of control is essential for coffee aficionados who understand that even minor adjustments in grind size can significantly influence the flavor profile of the brewed coffee.

In terms of technology, the Grindmaster 3311 often comes equipped with advanced grinding settings, allowing users to customize their grind based on specific brewing methods, whether it be for espresso, French press, or drip brewing. The dual hopper design is also an advantage, permitting users to switch between two different types of beans easily, thus offering flexibility depending on customer preference.

Additionally, the Grindmaster 3311 prides itself on quiet operation, utilizing sound-dampening technologies that minimize noise, creating a pleasant environment for both baristas and customers alike. Maintenance is also made simple, with easy access to the burrs for routine cleaning, ensuring consistent performance over time.

Energy efficiency is yet another characteristic that sets the Grindmaster 3311 apart. By utilizing innovative motor technology, this grinder reduces energy consumption without sacrificing performance, aligning with the growing trend toward sustainability in commercial operations.

In summary, the Grindmaster 3311 embodies excellence in commercial coffee grinding equipment. Its focus on grind quality, user-friendly technology, dual functionality, and energy efficiency makes it an invaluable asset to any coffee business dedicated to providing exceptional beverages to its customers.