Table Parts Breakdown | Grizzly G0656X instruction

Table Parts Breakdown

��

��

��

��	��	��
		��
		��
��		��	�
��		��	�
		��	�
	��		�
	��
	��
	��		��
			��
			��
			��
			��
			��

	��	��	��
	��
	��
	��
	��		��
	��		��
	��		��
	��		��
	��		��
	��	��	��
	��	��	��
		��	��
		��	��
			��
			��
			��
			��

	��	�
	��	�	��
	��	�

			��
			��
	�		��
	�		��
	�		��
	�		��

		�
		��
	��	��
	��	��
		��
		��
		��
		��
		��
		��
		��
		��

��

	��
	��	��
	��	��
	��	��
		��
		��

��

��

	��	��
		��
	��	��
	��	��
	��	��
	��	��
	��	��	��
	��		��
	��		��
			��

��

��

��

��

��

-40-	G0656 8" Jointer with Built-In Mobile Base

Image 56

Grizzly G0656X manual Table Parts Breakdown

Contents

To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Replacing Carbide Inserts Tools Needed Qty To rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List Description Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly Fasteners Qty Clean Up SeeAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory See Handwheels installed Perform Steps 18-26 on Pages 15 Model G0656 Page Table of Contents Foreword Contact Info Machine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Power Connection Device 220V OperationFull Load Amperage Draw Minimum Circuit Requirements Setup Safety Items Needed for SetupUnpacking Description Qty Inventory Cardboard Box Figure Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Assembly To assemble the jointer Checking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hose Recommended Adjustments Factory adjustments that should be verifiedTest Run Tighten V-Belt Operation Safety Jointer Overview Operations Basic Controls Start Button Starts motor Stock Inspection Requirements Scrape all glue off of boards before joint- ing Squaring Stock Surface Planing Edge Jointing To surface plane on the jointer Bevel Cutting To edge joint on the jointer Rabbet Cutting To bevel cut on the jointer To rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife Hone Dispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protection Schedule LubricationDaily Check Monthly Check Belts CleaningTo adjust/replace the V-belt Troubleshooting Motor & Electrical Cutting Setting/Replacing Knives Inspecting KnivesTo inspect the knives To set or replace the knivesPage Setting Infeed Table Calibrating Depth ScalePositive Stop Bolts Depth Stop Lever To set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See Figure Table Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns