FRONT PANEL DESCRIPTION

1.Power - Press this button to turn the unit on or off.

2.Headphone Jack - This connector accepts a 1/8" stereo/mono headphone connector. Stereo reception is possible only in the FM mode. All speaker outputs are automatically switched off when using the headphones.

3.Volume - With the receiver on, adjust this control clockwise to increase the audio level from the receiver's speaker, external speaker, or from headphones. Be certain to set the volume setting at the desired level for TIMER use.

4.Bass - This control adjusts the audio frequency response at the low end of the audio spectrum. Adjust clockwise for more bass response.

5.Treble - This control adjusts the audio frequency response at the high end of the audio spectrum. Adjust clockwise for more treble response.

6.Air Band Squelch - This control is operational only for the Aircraft band. The control allows muting of the receiver's audio when no signals are present. Adjust the control until background noise just disappears when no signal is being received.

7.Attenuator - Press to turn on the built in 20 dB attenuator to reduce the received signal strength in the AM broadcast and Shortwave bands as required. The attenuator is not active in the FM and Aircraft bands. Successive depressions of the button toggle the attenuator on and off.

8.AGC - Press to select either the Slow or Fast AGC setting for the AM broadcast, Shortwave and Aircraft bands. The AGC is not selectable in the FM mode.

9.Bandwidth - Press to select the desired bandwidth: 2.3 kHz, 4.0 kHz or 6.0 kHz. The bandwidth setting can be programmed to be automatic with mode selection, or manual. The default setting is for automatic selection. This function has no action in the FM mode. The 6.0 kHz bandwidth is automatically selected in the AM mode. The 2.3 kHz bandwidth is the default for the SSB modes. All three bandwidths are selectable by successive depressions of this button for the AM broadcast, Shortwave and Aircraft bands. To disable the automatic bandwidth selection with mode, start in the POWER 'OFF' mode and press and hold the BANDWIDTH button while pressing the POWER button to put the receiver in the POWER 'ON' mode. To enable the automatic bandwidth selection with mode operation, repeat the same procedure.

10.AM Sync - Press to select the AM mode of operation. Successive depressions toggle the synchronous detector on and off. Press to turn the synchronous detector off before selecting SSB modes. The 'AM' and 'AM SYNC' modes are not accessible in the FM band. The 'AM SYNC' mode is not accessible in the Aircraft band.

11.SSB USB-LSB-Press to select the SSB mode of operation ('SYNC' must be turned off). Successive depressions alternately select the 'LSB' or 'USB' modes as displayed. The SSB mode of operation is not accessed in either the FM or Aircraft band modes. Pressing the 'SSB USB-LSB' button while 'AM SYNC' mode is engaged will alternately select the upper or lower sideband portions of the AM signal being received.

12.Band - Repeatedly pressing this button will cycle through the Air (Aircraft), FM (FM Broadcast), SW (Shortwave) and AM (AM broadcast) bands.

13.LCD Display - The backlit, liquid crystal display provides the current status of the SATELLIT 800 MILLENNIUM such as frequency, mode, bandwidth, etc. Refer to LCD DISPLAY DESCRIPTION on page 14 of this manual for a full description.

14.Tuning - The 'TUNING' knob and the and buttons are the primary tuning controls of the SATELLIT 800 MILLENNIUM. Clockwise rotation of the dial increases frequency and counterclockwise rotation decreases frequency. The dial also incorporates variable speed tuning. The faster the dial is rotated, the faster the tuning

speed. The button increases and the button decreases the frequency by fixed steps (10 kHz or 9 kHz selectable in the AM broadcast band, 5 kHz on the Shortwave band, 100 kHz on the FM broadcast band and 25 kHz on the Aircraft band) with each depression. Pressing and holding either button will allow continuous stepping up or down as long as the button is depressed.

15. FUNCTION KEYS

STORE - This button is used to store the desired frequency, mode, attenuator, synchronous detector, AGC bandwidth, etc. as one of 70 memory channels. When pressed, the 'MEMORY' symbol will flash in the display. Enter a two digit number between '00' and '69' for the desired memory channel. An audible beep will indicate that the memory channel has been stored with the newly entered settings.

MEMO - To recall a memory channel at any time, press the 'MEMO' button and within three seconds of the button depression, enter a two-digit number between '00' and '69'. With 'MEMORY' displayed, other adjacent memory

channels can be recalled by use of the and buttons. The 'Tuning' knob may be used totune from the recalled frequency of the selected memory channel. Please note that numerical entries are interpreted as frequency entries if the 'MEMORY' channel number is not flashing.

12

Page 10 Page 12
Page 11
Image 11
Grundig 800 manual Front Panel Description, Function Keys
Page 10 Page 12

800 specifications

The Grundig 800 is a prime example of cutting-edge technology and classic design working in perfect harmony. This high-end audio product embodies superior sound quality, making it a sought-after choice for enthusiasts and casual listeners alike.

One of the standout features of the Grundig 800 is its advanced sound reproduction system. Equipped with powerful speakers and an efficient amplifier, it delivers crisp highs, rich mids, and deep lows. The sound stage created by the Grundig 800 allows listeners to experience their favorite music in a way that feels immersive and dynamic, as if they were part of the live performance.

In terms of connectivity, the Grundig 800 doesn't disappoint. It comes with various input options including Bluetooth, USB, and auxiliary ports, making it compatible with a wide range of devices. This versatility means users can easily connect their smartphones, tablets, or laptops to enjoy their favorite playlists or radio stations without any hassle.

The design of the Grundig 800 is equally impressive. Its sleek and modern aesthetics are complemented by a user-friendly interface. The clear display and intuitive controls ensure that users can navigate through options with ease. The use of high-quality materials gives the unit a premium feel and longevity, ensuring that it remains a staple in any audio setup for years to come.

Additionally, the Grundig 800 incorporates several cutting-edge technologies that enhance its performance. Features such as Digital Signal Processing (DSP) allow for optimized sound adjustments tailored to different environments, ensuring that audio playback is always at its best, regardless of the room’s acoustics. Furthermore, energy-efficient components contribute to a lower carbon footprint while maintaining high performance.

The Grundig 800 also places an emphasis on user experience with its smart features. Integration with voice assistants allows for hands-free control, making it simple to adjust settings or play music without needing to physically interact with the device. This convenience is a significant draw for modern users who lead busy lives.

In conclusion, the Grundig 800 stands out as a remarkable audio solution that combines exceptional sound quality, versatile connectivity, and intelligent features into a sleek and stylish package. Whether for home use, parties, or simply enjoying a quiet night in, the Grundig 800 represents the perfect blend of function, form, and cutting-edge technology.
Top Page Image Contents