Danger, Generac R | Guardian Technologies 04758-2 instruction

Installation and

Owner’s Manual

Air-cooled Automatic

Standby Generators

Models:

04758-2 (6 kW NG, 7 kW LP)

04759-2 (12 kW NG, 12 kW LP)

04760-2 (13 kW NG, 15 kW LP)

GENERAC RPOWER SYSTEMS, INC.

This manual should remain with the unit.

 Not intended for use as Primary Power in place of utility 

or in life-support applications.

DANGER

DEADLY EXHAUST FUMES. OUTDOOR INSTALLATION ONLY!

Page 1

Image 1

Guardian Technologies owner manual Models 04758-2 6 kW NG, 7 kW LP 04759-2 12 kW NG, 12 kW LP, Danger, Generac R

Contents

04760-2 13 kW NG, 15 kW LP Models 04758-2 6 kW NG, 7 kW LP 04759-2 12 kW NG, 12 kW LPThis manual should remain with the unit  Not intended for use as Primary Power in place of utility  ‹ OPERATION AND MAINTENANCE ‹ CONTENTS‹ HOW TO OBTAIN SERVICE INTRODUCTION and Adjustments Section 2 - Post Installation Start-upSection 4 - Maintenance Section 5 - Troubleshooting IMPORTANT SAFETY INSTRUCTIONS  GENERAL HAZARDS  WARNING  This product contains or emits chemicals  FIRE HAZARDS   ELECTRICAL HAZARDS  EXPLOSION HAZARDS  ‹ STANDARDS INDEX 1.2 PROTECTION SYSTEMS 1.1 UNPACKING/INSPECTION1.3 SYSTEM SET LED DANGER Figure 1.1 - 7 kW, Single Cylinder GH-410 Engine 1.4 THE GENERATORFigure 1.2 - 12 kW/15 kW, V-twin GT-990/760 Engine ‹ 1.5.1 GENERATOR 1.5 SPECIFICATIONS‹ 1.5.2 ENGINE 1.6 FUEL REQUIREMENTS AND RECOMMENDATIONS 1.8 RECONFIGURING THE FUEL SYSTEM1.7 FUEL CONSUMPTION DANGER ‹ 1.8.2 12KW AND 15KW, 990CC ENGINES 1.9 LOCATION‹ 1.9.1 GENERATOR Figure 1.4 - Demand Regulator 1.11 THE BATTERY 1.10 BATTERY INSTALLATION‹ 1.9.2 TRANSFER SWITCH 1.9.2.1 7 kW, 12 kW and 15 kW Units Figure 1.5 - Battery Cable Connections 2.1 BEFORE INITIAL START-UP 2.2 CHECK TRANSFER SWITCH OPERATION2.3 ELECTRICAL CHECKS Section 2 - Post Installation Start-up and Adjustments 2.5 CHECKING AUTOMATIC OPERATION 2.4 GENERATOR TESTS UNDER LOAD Figure 2.2 - Placement of Regulator 2.6 ADJUSTING THE REGULATOR NATURAL GAS ONLYFigure 2.1 - Dual Fuel Regulators Figure 2.3 - Single Cylinder Engine Governor Adjustment 2.7 ENGINE GOVERNOR ADJUSTMENTFigure 2.4 - V-twin Engine Governor Adjustment Figure 2.5 - V-twin Full Load Speed Adjust Screw 3.1 BREAK-IN PROCEDURE 2.8 VOLTAGE REGULATOR ADJUSTMENTFigure 2.6 - Voltage Adjustment Potentiometer ‹ 3.2.1 “AUTO” POSITION 3.4 SEQUENCE OF AUTOMATIC OPERATION 3.3 AUTOMATIC TRANSFER OPERATION3.5 MANUAL TRANSFER OPERATION ‹ 3.5.1 TRANSFER TO GENERATOR POWER SOURCE ‹ 3.5.2 TRANSFER BACK TO UTILITY POWER SOURCE 3.6 SETTING THE EXERCISE TIMER‹ 3.7.1 LOW OIL PRESSURE SWITCH Figure 3.2 - Manual Transfer Switch Operation Figure 3.3 - Low Oil Pressure and High Temperature Switches ‹ 3.7.2 HIGH TEMPERATURE SWITCH4.1 FUSE 4.2 CHECKING THE ENGINE OIL LEVEL ‹ 4.3.2 OIL CHANGE PROCEDURE 4.5 CHANGING THE ENGINE AIR CLEANER4.3 CHANGING THE ENGINE OIL 4.4 CHANGING THE OIL FILTER Figure 4.6 - 7 kW, Engine Air Cleaner Location 4.7 BATTERY MAINTENANCEFigure 4.7 - 12 kW and 15 kW Engine Air Cleaner Figure 4.8 - Setting the Spark Plug Gap Figure 4.10 - Valve Clearance Adjustment 4.8 ADJUSTING VALVE CLEARANCE4.9 COOLING SYSTEM ‹ 4.12.1 REMOVAL FROM SERVICE 4.12 OUT OF SERVICE PROCEDURE‹ 4.12.2 RETURN TO SERVICE 4.10 ATTENTION AFTER SUBMERSION ATTENTION It is recommended that all service work 4.13 SERVICE SCHEDULEbe performed by the nearest Authorized Dealer Problem 5.1 TROUBLESHOOTING GUIDECause Correction Section 6 - Electrical Data ENGINE WIRING CUSTOMER CONTROL PANEL BOXCONNECTION Electrical Schematic - 12 & 15 kW - Drawing No. 0D8501-B Section 6 - Electrical Data Section 6 - Electrical Data ENGINE WIRING CONTROL PANEL BOX 224A 225A Electrical Schematic - 7 kW - Drawing No. 0D9014-C PRE PACKAGED UNITS ONLY Section 7 - Exploded Views and Parts Lists CLOTH, HARDWARE 266.7mm x 146mm 7KW PART NO. QTY. DESCRIPTIONFOAM, EXHAUST SIDE ENCLOSURE FRONT FOAM, BACK EXHAUST ENCLOSURE COVER Section 7 - Exploded Views and Parts Lists DESCRIPTION PART NO. QTY 66 2, 5, 19, 20, 39, 40, 47, 64, 93 67 8, 11, 12 68 4, 5 Views and Parts Lists69 16A, 16B, 17 72 27, 28 73 3, 32, 33, 34, 35, 36, 40 ASSEMBLY, CRANKSHAFT HORIZONTAL ASSEMBLY, CRANKCASE HOUSING WITHITEM PART NO. QTY. DESCRIPTION ROLLER BEARING, GOVERNOR PLATE Section 7 - Exploded Views and Parts Lists ASSY, IGNITION COIL GV-990 CYLINDER 7 kW Generator - Drawing No. 0D3504-E 1.25 FT 1.8 FT 32 31 12 kW and 15 kW Generator - Drawing No. 0D3417-L 3 FT 2.6 FT1.44 FT Section 7 - Exploded Views and Parts Lists DESCRIPTION Section 7 - Exploded Views and Parts Lists Section 7 - Exploded Views and Parts Lists DESCRIPTION Section 7 - Exploded Views and Parts Lists Section 7 - Exploded Views and Parts Lists DESCRIPTION Section 8 - Mounting ALL DIMENSIONS IN MILLIMETERS INCHESDrawing No Air-cooled Section 9 - Notes MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE YOUR WARRANTY RIGHTS AND OBLIGATIONSPURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT EMISSION RELATED PARTS INCLUDE THE FOLLOWING EMISSION CONTROL SYSTEM WARRANTY WARRANTY SCHEDULE GENERAC POWER SYSTEMS TWO YEAR LIMITED WARRANTY FOR GUARDIANTHIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING PREPACKAGED EMERGENCY AUTOMATIC STANDBY GENERATORS

Guardian Technologies 04758-2, 04759-2 owner manual 04760-2 13 kW NG, 15 kW LP, Danger, Generac R

Models: 04759-2 04758-2 04760-2

Installation and

Air-cooled Automatic

Models:

04760-2 (13 kW NG, 15 kW LP)

This manual should remain with the unit.

 Not intended for use as Primary Power in place of utility 

or in life-support applications.

DANGER

Installation and

Air-cooled Automatic

Models:

04760-2 (13 kW NG, 15 kW LP)

*This manual should remain with the unit.*

 Not intended for use as Primary Power in place of utility 

or in life-support applications.

DANGER

This manual should remain with the unit.